Search results

The final release of the SiC membrane, to define a CMUT, is also presented using a simple thermal treatment to reduce the total number of technological steps.
A higher magnified image of such a surface is presented in Fig.2d where small grains can be seen.

Fig.3 T[O] and [N] in the edge of the first slab Fig.4 T[O] and [N] in the middle of the first slab Table.2 T[O] and [N] of the normal slab Number Edge Middle wT[O]×10-6 w[N]×10-6 wT[O]×10-6 w[N]×10-6 1# 2# 28 26 27 26 24 23 25 25 Average 26 24.5 26 25.5 Micro-inclusions Analysis.
Parts of TiN inclusions exist on the surface of Al2O3 inclusions. ② SiO2 inclusions: 50~150μm, come from slag entrapment in tundish or stuffing sand. ③ Al2O3 inclusions: less than 30μm, grain and tufted.

The average grain size based on SEM characterization is larger than the W-H calculation.
The formation of Mn3+-O2--Cr3+ interactions can occur because Cr3+ has the same number of electrons (isoelectronic) as Mn4+ (3d3, t32g↑ e0g↑) ions [10].

In a uniform carbon dioxide corrosion of carbon steels a great number of transport, chemical and electrochemical processes may occur.
The API N80 microstructure consists of acicular ferrite and bainite with carbides precipitated on grain-boundary.

Introduction Glass materials have attracted the attention of many research due to their properties, which are different as compared to crystalline materials, such as isotropic conduction, absence of grain boundaries, ease of fabrication into complex shapes, wide compositional flexibility, and high ionic coupled with low electronic conductivity [1].
Atomic ring size was calculated based on the value of the first order stretching force constant and coordination number of each chemical oxide used in the experiment and also bulk modulus of the glasses.

Generalized hyperbolic distribution(GH) was introduced by Barndorff-Nielsen in 1977 when he studied the grain size distribution of wind blown sands[1].
Step 1 generate random sample (N=2819) from a pdf defined by normal distribution, generalized hyperbolic distribution , normal inverse distribution, hyperbolic distribution whose parameters listed in the table 3 had been estimation by patter search algorithm; Step 2 compute and according to the formula (4) and (5); Step 3 repeat step 1 and step 2 10000 times and we get 10000 and ; Step 4 Desending the above 10000 and ,then the 100-th number is the critical value of goodness of fit(10000*1%=100,1% is the significance level).

A number of researchers have described relationships between factors affecting the performance of the delivery grinding fluid to grinding zone.
The grinding wheel is a porous solid disk consisting of abrasive grain, bond materials and pores of irregular shapes and different sizes.

The digital image processing is performed in the detection thread to estimate the amount of wear, which decides the dressing depth to remove the worn abrasive grain.
Table 1 Experimental conditions Parameters Value/Specification Model of Machine MD9040 Number of control axis 6 Grinding method Dry point-grinding Grinding wheel 1A1/T2 200×6×32×4 MBD3 120/140 M75 CCD camera COSTAR M3501/2" B&W 752™582 Diamond dresser Single-point diamond tool Accelerometer 333B32 (PCB)

A great number of zeolite structures without natural counterpart have been constructed by human beings.
The results of the test show that the permeation ratio of N2 through the membrane was 0 before calcined, for the templates has filled the channels of zeolite membrane and the gaps between crystal grains.

The heat treatment carried out cause in the solution treatment process solving in the solid solution of the big precipitations of the intermetallic phases, whereas during the ageing the homogeneous precipitation occurs of the dispersive intermetallic phases in the whole volume of the matrix grains.
Such structural state adds to the significant reduction of the number of locations in which corrosion centres may form.