Search results

Table 1.
Fig. 1.a shows the curves of changes in the contact angle q depending on the content of aluminosilicate microspheres (10, 20, 30 wt.%) and AEROSIL (0.5, 1.0, 1.5 wt.%) and with their compatible introduction to the coating composition (Fig. 1.b).
References [1] Yu.S.
Voliuvach, University Publishing House, (2010) 475-479
IOP Publishing, 708 (2019) 012103 p. doi:10.1088/1757-899X/708/1/012103 [15] K.

The minimum pH was kept at 10 by additions of KOH 0.1 mol L-1.
Fig. 1.
This sample also exhibited peaks at 406, 442 and 479 cm-1 assigned to n2 PO43- as well as at 1026, 1064 and 1081 assigned to n3 PO43- of b-TCP [13,15].
References [1] J.
Nanobiotech. 1 (2010) 42-49

Fig. 1.
Table. 1 Thickness cases of patchwork HF part No.
For lightweight in solution 1, 1.02kg was decreased about 22% to the benchmarking car and 1.53kg decreased about 33.3% in solution 2.
References [1] Karbasian, H., Tekkaya, A.E., 2010.
SAE International Journal of Materials and Manufacturing 1 (1), 472–479

Scheme 1.
Fig. 1.
Their photoluminescence properties are presented in Table 1.
The results are shown in Table 1.
References [1] H.

ribbon edge center Figure 1.
The average Vickers hardness of the ribbon is 479 HV, which values is considerably higher than that of a melt-spun Mg-Cu-Y alloy [23].
TÁMOP 4.2.1.
/B-09/1/KMR-2010-0003.
References [1] L.

A final annealing treatment was carried out at 750 °C for 1 hour in vacuum.
The alloy composition is listed in Table 1 and the photograph of 14Cr ODS-FeCrAl cladding tubes is shown in Fig.1.
Table 1 Chemical compositiond of ODS-FeCrAl alloy (wt%).
References [1] B.
Mater. 479 (2016) 36-47

The HAp-Zn/SA was prepared with a certain ratio of PBS: Sample (1:1).
Fig. 1.
Table 1.
References [1] E.
Charact., vol. 62, no. 5, (2011) 469–479

Table 1 Forming parameters of the surface films on AZ91D alloy melt.
Fig. 2 EDS-spectra and compositions from (a) Outer layer, (b) Regular particle, (c) Irregular particle shown in Fig. 1(a) and (d) Surface shown in Fig. 1(b).
Conclusions 1.
References [1] Wang Xianfei, Xiong Shoumei, J.
Forum. 475-479 (2005) 2543-2546

Ho2O3 and TiO2 powders were used in the molar ratios of 1:2, 3:4 and 1:1 to produce sintered oxide pellets of composition Ho2+xTi2-xO7-x/2 (x=0, 0.4 and 0.67) (or Ho2Ti2O7, Ho1.5TiO4.25 and Ho2TiO5), respectively.
Results and discussions Fig.1.
References [1] R.C.
Alloys and Compounds. 479 (2009) 6-10
Lett. 28 (2011), 066102(1)-066102(4).

A Reasoning Method of Transformer Fault Causes Based on Fuzzy Petri Net Weihua Zhang 1,a, Jinsha Yuan 1, Ke Zhang1, Zhong Li 1 1 School of Electrical and Electronic Engineering, North China Electric Power University, China azwhhdbd@126.com Keywords: fuzzy Petri net, transformer, fault causes reasoning, production rule.
According to Reference [11], the analysis on causes of overheating fault is shown in Table 1.
References [1] X.
Power System Technology, Vol.32,No.1,(2008),p.46-50
The analysis and processing of iron core multipoint earthing fault on No. 1 Main Transformer in 110kV substation.