Search results

The PP/Co-PP exhibited lower yield strength and young’s modulus, and higher elongation at break than talc composites (data not show here).
Copolymer polypropylene tends to have better stress crack resistance and lower temperature toughness than homopolymer at the expense of slight reductions in other properties.

Based on data analysis, the average value of the three antioxidant activity of the replication was 2.482 mg QE / g Extract on the skin of ginger bud fruit and 99.846 mgQE / g extract for lontar fruit skin.
Antioxidants are compounds capable of donating a single electron or hydrogen atom for reduction(8).

The cyanide leaching reaction mechanism is also discussed.The data at different cyanide concentrations, different temperature and different oxygen pressure are obtained.
The dissolution mechanism involves an electrochemical process in which the anodic reaction is palladium oxidation while the cathodic reaction is oxygen reduction.

Compared to the commercially available 1200 V SiC DMOSFET, this new concept has significantly reduced the specific on-resistance (Ron) and gate-drain capacitance (Cgd) simultaneously, produced a record low Ron·Qgd Figure of Merit of 455 mΩ·nC at 25⁰C, and 700 mΩ·nC at 150⁰C (~30% of the best data found).
The experimental results on a 1600 V, 20 A SiC CIMOSFET have shown only a 55% increase in on-resistance at 150⁰C, and over 60% reduction in the gate-drain capacitance which results in a record low Ron·Qgd Figure of Merit on 1200 V rated SiC MOSFETs, to the best of our knowledge.

The results were compared with the experimental and simulation data from the open literature.
Aldushaishi, “Investigation of Drillstring Vibration Reduction Tools,” Missouri University Of Science and Technology, 2012

Experimental data show that milling with the formation of a magneto fluidized bed allows intensifying the process.
Dornfeld, Energy consumption characterization and reduction strategies for milling machine tool use, in: J.

HOMER Pro capabilities Input data used for simulation to determine the optimal size of hybrid renewable energy systems with HOMER Pro include the meteorological data, load profile, equipment characteristics, search space, economic and technical data.
Meteorological data consist of wind speed, solar radiation, temperature, and stream flow.
These data are also used into the software as daily profile for power balancing constraint.
In the same vein, technical data are also required for the simulation, these data are dispatch strategy, maximum annual capacity shortage, minimum renewable energy fraction and operating reserve.
Data Commun.

This is due to a significant reduction in drawing information usually generated for producibility.
Data model for milling can be referring to ISO 14649 Part 12 Process Data for Turning.
TURN-MILL A combination between data model for milling (ISO 14649 Part 11 Process Data for Milling) and data model for turning (ISO 14649 Part 12 Process Data for Turning).
Hence, bi-directional data exchange is enabled.
Data storage ISO10303-28 specifies the extensible markup language (XML) representation for EXPRESS-driven data and is officially known as STEP-XML.

Anaerobic digestion process for reduction of the pollution in palm oil mill effluent (POME) is advantageous before POME is released to the environment.
Kinetics calculation: Kinetics parameters corresponding to the biohydrogen production were calculated from the cumulative hydrogen production versus time data.
The cumulative hydrogen production versus time data was fitted with modified Gompertz equation (Eq.1) [8] to determine the hydrogen production potential (Hmax,v), hydrogen production rate (Rmax,v) and lag phase ().
Each data point represents average value of duplicate experiment (n=2) and I-bar represents standard deviation.

The experimental data in the stall speed is 0.2-0.5xrotating stall frequency.
Table 1 Two measuring points bearing fault characteristic frequency (Hz) Transponder Cage Rolling Body outer Inner 16.42 7.064 56.86 134.22 177.76 Data Acquisition and Analysis Waterfall Graph Analysis.
Select measuring point 2 data, cepstrum analysis of them as shown in Figure 7.
Inlet flow reduction is a common cause of fans rotating stall.