Search results

Introduction Synchrotron X-ray topography (SXRT) is a non-destructive technique that images structural defects (dislocations, stacking faults, grain boundaries, etc.) in bulk crystals, epitaxial films and wafers fabricated for electronic devices [1-5].
Department of Energy, under Award Number DE-AR0001028.

Thus, during the Portland cement clinker minerals hydration, a wide range of neoplasms are formed, and during the hardening of silicate materials based on aluminosilicate raw materials and lime under non-autoclave conditions, a limited number of types of neoplasms are formed [14-15] in the system CaO-SiO2(Al2O3)-H2O.
The influence of quartz grain size within the system CaO–SiO2–D2O, Progress in Crystal Growth and Characterization of Materials. 58 (2-3) (2012) 84-91

Poplar, due to its abundant resources and advantages of short growth cycle, straight grain, even texture, etc., is increasingly used in wood industry of China.
Acknowledgment This work was supported by the State Forestry Administration of China through grant number 2011-4-12 and a Project Funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions.

The method of combination large deformation meets the study of supersteel and ultrafine grained steel[7].
In order to develop new kinds of steel such as surface treatment strip steel, stainless steel that owns well performance, electric steel Fig.3 straight-pull reversing cold strip mill etc., we need to adopt different annealing treatment for sheet and strip, this need many kinds of theory research and large number of experiments.

Arrays of parallel layered surfaces are observed in the SEM picture (Fig.4a) for the film deposited at a solution pH 1.5 Small pores are also observed on the surface and fine grains are not observed in the micrograph.
Co-Ni alloy film prepared at solution pH 3.5 (Fig.4b) reveals comparatively a smooth surface and the number of pores is found to be reduced.

Introduction Magnesium alloys, due to their low densities and good casting properties, are attractive materials for use in certain machine housings, automotive, aerospace, and a number of other applications.
SEM observation and EDS analysis of debris removed from the composite sample (Fig.14) revealed the presence of very fine grained GCp surrounded with metal or oxide molecules.

One of the main contributors to poor removal rates for the colloidal silica CMP process is its tendency to selectively etch defects, grain boundaries and scratches.
Acknowledgement The work presented was funded by DARPA/MTO - contract number DAAD19-02-1-0231.

Operating parameter optimization and treatment effect of PFS Table 2 Raw water quality in PFS orthogonal test Items pH Turbidity/NTU CODcr/(mg/L) TN/(mg/L) TP/(mg/L) Values 7.94 616 1097.6 101.2 5.78 The final removal rate of TP is treated as index, the following four factors are treated as the main investigate factors: A (mixing intensity), B (stirring time), C (dosage), D (different pH values), each of the factors are designed three levels, so as to establish four factors and three levels orthogonal test factor table, so select the orthogonal table L9 (34) to arrange test: Table 3 Factors and standards of orthogonal test Standard A B C D Stirring intensity r/min Stirring time s Dosage mg/L pH 1 200 30 50 6 2 250 60 75 7 3 300 90 100 8 Table 4 Orthogonal test result of sanitary waste water treatment by PFS Ordinal number A B C D TP removal rate% Stirring intensity r/min Stirring time s Dosage mg/L pH 1 200 30 50 6 20.69 2 200 60 75 7 39.66 3 200 90 100 8 58.62 4 250 30 75
That is to say, the active PAM carbon chain functional groups adsorb the tiny uniform particle and viscous grain in dispersed phase to form flocculent mass linked to each other and become bulky flocculent body.

The architecture framework with exception handing in SOA WU Qing 1, a, YING Shi 1, b, NI You-Cong 2, c, CUI Hua 1, d 1 State Key Laboratory of Software Engineering, Wuhan University, Wuhan, China 2 Department of Mathematics and Physics, Anhui Institute of Architecture & Industry, Anhui, China a 12capricorn@163.com, b yingshi@whu.edu.cn, cnyc@mail.whu.edu.cn, dcuihua_com@126.com Keywords � SOA, reflection, exception handling Abstract�Service-oriented software systems are inherently complex and have to cope with an increasing number of exceptional conditions in order to meet the system's dynamic requirements.
In the International Organization for Standardization W3C's "Web Services Architecture" [1] document that the service-oriented architecture is distributed system architecture, usually with a message-oriented-oriented description, coarse-grained, platform-neutral and so on.

Projects such as the European Extremely Large Telescope provide a relevant case study, where significant numbers of high-value bespoke optics are required.
Photomicrograph images of grains, and particle-size distributions from image-analysis, are presented in Figs. 4 and 5 respectively, and confirm a tail long-wards of the peak, which will influence texture.