Search results

Table 2 Experiment conditions Experiment Conditions Parameters Convergent-Divergent Nozzle Throat Diameter 1.5 mm Outlet Diameter 5mm Convergent Nozzle Outlet Diameter 1.5mm Mixing Chamber Diameter 50mm,200mm Diffuser Throat Diameter 5,6,7mm Outlet Diameter 30,40,50mm Temperature of Strong Solution 18℃ Concentration of Strong Solution 50.7wt% Flow Rate of Strong Solution 1.2 kg/min ~2.7 kg/min Evaporating Temperature 5℃ Additive Without Isooctanol/ Isooctanol（50mg/kg） Back Pressure of Diffuser 500Pa Data Reduction The heat and mass balance for the absorber are expressed respectively as hSinWSin+hVinWab=QC+hSout(WSin+Wab) (1) Winxin=(Win+Wab)xou (2) Where h is the enthalpy, W is the mass flow rate, Wab is the mass flow rate of absorbed vapor, x is the mass fraction of LiBr, QCis the

WANG [7] puts forward the notion of Electric Pulse Modification(EPM), based on experimental data [8~10].
The effects on microstructure of alloys include reduction of the grain size, control of columnar structure, formation of equiaxed grains, improvement of material homogeneity, and the uniform distribution of second phases.

The test data were recorded until the sample breakage, then circulating hysteresis loop and low cycle fatigue life curve was drawn.
The strain amplitude changed from 0.05mm to 0.25mm leaded to the reduction of the low cycle fatigue.

An energy level for 6 dB, from (6) formula can be obtained: (7) From (7) formula obtaine the reduction of RF signal power after it through indoor spread
Make sure good dependent and independent variables of and , make Lagrange interpolation according to the discrete data.

The analysis results can be referenced as theoretical guidance for structure optimum design and manufacturing cost reduction.
Fig. 5 Equivalent stress variation curves along different evaluation paths Table 1 Maximum equivalent stresses on different stress evaluation paths Path number Membrane (MPa) Membrane plus bending (MPa) Total (MPa) 1 40.12 84.25 90.74 2 33.25 82.03 94.22 3 44.45 66.49 62.83 4 45.38 58.16 62.85 Substituting the stress data of Tab 1 in the stress checking and restrictive conditions, the strength checking conclusions of diaphragm chamber can be calculated by following inequalities.

System Active Dissipation Data Algorithm GA TS TSGA Active Dissipation with optimization 0.0514 0.0511 0.0508 Active Dissipation Reduction (%) 25.94 26.37 26.80 Table 1 shows the system dissipation declines with the three algorithms and the Taboo Search employs higher performance for global search and can jump efficiently from the local optimal solution. 4.1 Average Convergence Characteristic The average convergence characteristic for the fifty operations in GA, TS and TSGA is in Fig. 2. 4.2 Distribution of the Object Function Value The distribution of the object function value for the fifty operations is shown in Fig. 3, which indicates the average value and variance of final object function with the method of GA are 0.0514 and 0.0005868, and corresponding values with TS and TSGA are 0.0511, 0.0009726 and 0.0508, 0.0008249.

Electrical demand curve in Spain in a typical day Flow batteries Like any type of electrochemical battery, flow batteries are based on reversible electrochemical reactions of oxidation and reduction (redox) reactions that occur in cells connected in series and/or parallel to obtain the desired voltage in the charging (electric energy storage) or discharging process (transfer of electricity to the electrical load) [2-4].
Springer-Verlag, Berlin (2007) [8] Michalewicz, Z.: Genetic algorithms + data structures = evolution programs. 3rd edn.

On the other hand, the uncontrolled reduction of output rate in the video encoders will lead to unnecessary decrease in quality and inefficient utilization of the current web resources.
If the object is relatively still in a level, or the data of a level has little difference from that of the previous level, then such a level is called Motion level[6-7]; if the fields of the successive levels change, or the moving object hasn’t the best match in the previous level, then it is called High Motion level[8].

In the case of open-Chains or with few closed loops, such as in robotics, relative coordinates are particularly suitable; when this coordinate method is used for systems with complex closed loops, the reduction to minimal form is still a tricky problem.
Fig. 5(a) shows the animation of motion of Big Pendulum Hammer and Fig. 5(b) shows the data plot.

These phases also can be formed when a potential imposed to the system causes the reduction of chalcopyrite, which allows the extraction of iron from the crystalline structure, forming copper sulfides that are more susceptible to oxidative leaching.
The final residues of bioleaching were analyzed by XRD (data not shown) and revealed the presence of chalcopyrite and the formation of jarosites, and no sulfur was detected.