Search results

By this method, stresses were determined from the measured strain based on the elasticity of materials.
Current Opinion in Solid State Materials Science (1996) 1:679 – 683
Materials Science and Engineering.
Journal of Materials Science 39 (2004) 2865 – 2867
New Class of Layered Materials.

Microstructures of the as-cast materials were as presented in Fig. 1.
Ikenaga: Journal of Materials Science and Technology Vol. 23 (2007), p. 97 [2] M.
Santos: Metallurgical and Materials Transactions AVol. 28 (1997), p.2015 [8] J.
Insausti: International Journal of Metalcasting Winter 10 (2010), p.51 [9] G.
Hafiz: Journal of Materials Science Vol. 36 (2001), p.1293 [12] M.

Titanium alkoxide and corresponding solvent as raw materials were used, then a certain amount of water, acid and complexing agent were added after mixing and aging, Stable sol was obtained.
Zhao: Journal of Inorganic Materials, Vol. 15(2000) No.2, p.347.
Stefanov: Journal of Materials Science, Vol. 28 (1993) No.5, p.1276
Zhang, et al: New Chemical Materials, Vol. 37 (2009) No.10, p.76.
Science[J]. 2001,293(5528):269-271

Introduction Polyurethane (PU), one of the six main categories of synthetic materials in the world, are developed very fast and widely used in transportation, furniture and building industry, etc [1].
Li: New Chemical Materials, Vol.38 (2010) No.5, P.112 (In Chinese) [4] E.
Zhang: Advanced Materials.
Xue: Journal of Changchun University of Technology, Vol.28 (2007) No.1, P.17.
Duan: Journal of Wuhan university of Technology, Vol.31 (2009) No.21, P.5.

Aluminum alloy drill pipe With the advances in materials science and processing technology, aluminum alloy drill pipe in the drilling industry has been increasingly widely used [2,3,4].
So Al alloy 7075 was chosen as experimental material, material properties at room temperature are: σb ≥ 500MPa; δ = 11 ~ 13%.
While hot extrusion above the recrystallization temperature, extrusion speed and temperature will have a significant impact on the flow stress of different materials.
Arabian Journal for Science and Engineering[J], Vol.37, Issue8, 2012, p.2287-2296 [7] Hossein Mohammadi, Mostafa Ketabchi and Ali Kalaki: Microstructural evolution and mechanical properties of back-extruded Al 7075 alloy in the semi-solid state.
International Journal of Material Forming[J], Vol.5, Issue2, 2012, p.109-119 [8] Jian-xin Xie, Jiang-an Liu: Theory and technology of metal exrusion[M].

Owing to the mortar material nonhomogeneous, when the foreside unit of the crack has not had the damage destruction, the units of the mortar specimen which intensity are smaller had been damage destruction.
Key Engineering Materials Vol.265(2004) ,p. 1517-1522 [2] Zhu Wan-cheng, Tang Chun-an, Huang Zhi-ping, Pang Ming-zhang.
Chinese Journal of Rock Mechanics and Engineering Vol.24(2005),p. 1-7 [3] Zhu Wan-cheng, Tang Chun-an,Qi An-wen.
Journal of Northeast University(Natural Science),，Vol.20（1999）,p. 533-535 [5] Zhu Wan-cheng, Huang Ming-li, Tang Chun-an.
Journal of Liaoning Technical University (Natural Science) Vol.19（2000）,p. 271-274 [6] Yao Xue-feng, Xiong Chun-yang, Fang Jing.

Establishment of the Non-linear Finite Model Model Design and Material Selection.
Fig. 1 The sectional dimension and reinforcement of specimen [mm] Table 1 Mechanical properties of materials Materials fy [Mpa] Poisson ratio Elastic modulus [Mpa] Concrete -- 0.167 2.648×104 Longitudinal bar 335 0.3 2.0×105 Stirrup 335 0.3 2.0×105 Constitutive Relations of Materials Constitutive Relation of Concrete.
Liu, Shaking table test and theoretical analysis on RC frame-short pier shear wall structure with special-shaped columns, Journal of Xi’an University of Architecture & Technology, Natural Science Edition, 39 (2007) 610-615
Yao, Dynamic characteristics of flange frame column structure, Journal of Architecture and Civil Engineering, 6 (2009) 57-62
[10] Hasan Kaplan, Salih Yilmaz, Seismic strengthening of RC structures with exterior shear walls, Indian Academy of Sciences, 36 (2011)17-34.

Introduction Potassium dihydrogen phosphate (KDP) crystal is a soluble material in water with positive solubility coefficient [1].
Rapid growth of KDP-type crystals, Progress in Crystal Growth & Characterization of Materials. 43.1(2001)1-118
Optical, structural and microhardness properties of KDP crystals grown from urea-doped solutions, Materials Research Bulletin. 43.10(2008) 2778-2789
[6]Wang K, Lu G, Zhou G, et al.Molecular Dynamics Study on Microstructure of Potassium Dihydrogen Phosphates Solution, Chinese Journal of Chemical Physics. 23.2(2010)160-164
Rapid growth of a large-scale(600 mm aperture) KDP crystal and its optical quality, High Power Laser Science and Engineering. 2.1(2014)40-44

[9] Section III military products, multi-disciplinary design optimization technical workshop materials [C].
[15] Renaud JE, Approximation in Nonhierarchic System Optimization, AIAA Journal, Vol32, No.1, Journal 1994
Journal of Astronautics, Vol, 25.No 4.July 2004
Journal of Ship Mechmice Vol.8.No.6.Dec, 2004
Journal of Northwestern Polytechnical University. 2007.3

Selvaduray, Effects of welding on the passive oxide film of electropolished 316L stainless steel, Journal of Materials Processing Technology, 166 (2005) 30-43
Arivazhagan, Argon and argon-hydrogen shielding gas effects on the laves phase formation and corrosion behavior of Inconel 718 gas tungsten arc welds, Journal of Materials Processing Technology, 263 (2019) 374-384
Kim, The effect of alternate supply of shielding gases in austenite stainless steel GTA welding, Journal of Materials Processing Technology, 209 (2009) 4722-4727
Shukla, Microstructural and electrochemical evaluation of fusion welded low-nickel and 304 SS at different heat input, Journal of Materials Engineering and Performance, 26 (2017) 5847-5863
Rajendra Kumar, Delta ferrite in the weld metal of reduced activation ferritic martensitic steel, Journal of Nuclear Materials, 455 (2014) 343-348