Sort by:
Publication Type:
Open access:
Publication Date:
Periodicals:
Search results
Online since: July 2011
Authors: Tian Lin Song, Zhi Yao Li
Dictionary - View detailed dictionary
1. noun
1. reduction
2. reducing
2. verb
1. reduce
2. decrease
3. lower
4. lessen
5. cut back
6. subside
Figure 2.3 3D Image of snake-like robot
Controlling System of Snake-like RobotListenRead phonetically
Dictionary - View detailed dictionary
1. noun
1. disassembly
2. destruction
2. verb
1. disassemble
2. dismantle
3. unload
4. knock down
The control system of snake-like robot is showed in Fig. 3.1.
The remote control receiver module fixed on snake body receive the command and convert it to level data, then send them to main control module (AT89C2051 microcontroller used in this design).
The remote control receiver module fixed on snake body receive the command and convert it to level data, then send them to main control module (AT89C2051 microcontroller used in this design).
Online since: August 2013
Authors: Wen Hong Liu, Xin Wu
Test case design is to determine a set of test data which most likely to find an error or class of errors.
ACM Transactions on Software Engineering and Methodology 2(3), 270–285 (1993) [5] Chen, T.Y., Lau, M.F.: A New Heuristic for Test Suite Reduction.
ACM Transactions on Software Engineering and Methodology 2(3), 270–285 (1993) [5] Chen, T.Y., Lau, M.F.: A New Heuristic for Test Suite Reduction.
Online since: June 2014
Authors: Li Ping Xiao
In addition, there are reduction factor exist: when rock and tunnel has an angle of 10 to 20 degrees, the factor is 0.8, and hence for IV category rocks, it can only withstand 1.6 to 0.45 MPa of pressure.
Now, the slope of those three pitshafts are 22, 25, 25 degree separately, and according to drilling data the angle of drilling is 17~18 degrees.
Now, the slope of those three pitshafts are 22, 25, 25 degree separately, and according to drilling data the angle of drilling is 17~18 degrees.
Online since: October 2013
Authors: Er Qiang Wang
These parameters were referenced from relevant document [3] to close to real plant data.
(a) (b) (c) Fig.3 Change of reflux ratio and heat load of reboiler and condenser with feed stage or vapor fraction of feed (a)primary tower, (b)rectification tower (c) primary tower The minimum reflux ratio can be found by increasing the number of stages until there is no further reduction in the reflux ratio.
(a) (b) (c) Fig.3 Change of reflux ratio and heat load of reboiler and condenser with feed stage or vapor fraction of feed (a)primary tower, (b)rectification tower (c) primary tower The minimum reflux ratio can be found by increasing the number of stages until there is no further reduction in the reflux ratio.
Online since: July 2014
Authors: Bin Jia, Ru Heng Wang, Ke Li, Jun Mo
And the destruction of the BFRP test is also began from the middle area, the simulation results are matched with the experimental data.
It shows that BFRP provided effective constraint, but it also can be seen that stress of BFRP is not reach its tensile strength, and it is matched with a consistent reduction factor mentioned in the reference[5].
It shows that BFRP provided effective constraint, but it also can be seen that stress of BFRP is not reach its tensile strength, and it is matched with a consistent reduction factor mentioned in the reference[5].
Online since: August 2013
Authors: Yan Jun Hu, Yan Liang Du
The water-reduction amounted to 26%.
Cement and Concrete Research, 29 (1999) 487–495 [4] P.B.Baforth, The deviation of input data for modeling chloride ingress from eight-year UK coastal exposure trials, Magazine of Concrete Research, 1999(2): pp87~96.
Cement and Concrete Research, 29 (1999) 487–495 [4] P.B.Baforth, The deviation of input data for modeling chloride ingress from eight-year UK coastal exposure trials, Magazine of Concrete Research, 1999(2): pp87~96.
Online since: August 2013
Authors: Mihaela Urdea
The main advantage of harmonic gears is that the very small masses can perform very high levels of reduction.
The input data for configuring this assembly are: output shaft engine speed, power output shaft, power input shaft, moment of torsion on input shaft and harmonic gear efficiency.
The input data for configuring this assembly are: output shaft engine speed, power output shaft, power input shaft, moment of torsion on input shaft and harmonic gear efficiency.