Search results

However, most of the current research on current density is not systematic, and there are few comprehensive studies on how current density affects the surface, internal structure and mechanical properties of copper foils.
However, in the stage of low current density, due to the low electrodeposition rate, low crystal nucleation rate, as well as the good symmetry and stable structure of the {111} crystal surface, a small amount of {111} crystal surfaces can be found.
Journal of Electroanalytical Chemistry, 588(1) (2006) 88-98.

Simulation and Optimization on Silicon Carbide Synthesis Furnace Power Curve Yonggang Li a, Yangdong Hub, Qinhe Sun, Lianying Wu College of Chemistry and Chemical Engineering, Ocean University of China, Qingdao 266100, P R China ali.yonggang@126.com, bydhuhd@ouc.edu.cn Keywords: SiC, finite element, thermal-seepage couple, power curve optimization Abstract.
The structure of SiC furnace is that the core is made of graphite powder in the centre of furnace and the outside of furnace core is SiC synthesis material.
Swain: Structure and Properties of Ceramics-volume 11 of Materials Science and Technology.

Rusop3,h 1Department of Physics, Faculty of Science and Mathematics, Universiti Pendidikan Sultan Idris, 35900 Tanjung Malim, Perak, Malaysia 2Department of Chemistry, Faculty of Science and Mathematics, Universiti Pendidikan Sultan Idris, 35900 Tanjung Malim, Perak, Malaysia 3NANO-SciTech Center, Institute of Science, Universiti Teknologi MARA, 40450 Shah Alam, Selangor, Malaysia.
In the meantime the samples were also covered with non-tubular carbon structure and soot with large diameter.
This indicated that the VACNT synthesized at 800°C have better graphite structure than those synthesized at lower and higher synthesis temperatures.

At the beginning hydrogen desorption occurs through the Mg2NiH4 phase, which surface structure appears cleaner than of MgH2.
In the first attempt we have modified the surface chemistry by adding graphite and C-rich organic additives.
The lubrication effect prevents back agglomeration of Mg particles and both additives react with Mg to form a modified surface structure.

The electrochemistry behaviour of carbon steel in 55% LiBr solution with A-Mo inhibitor Jielan Li 1,2,a, Chenghao Liang 1,b,* and Naibao Huang 1,c 1 Transportation Equipments and Ocean Engineering College, Dalian Maritime University, Dalian 116026, China 2 School of Chemistry and Chemical Engineering, Liaoning Normal University, Dalian 116029, China a lijielan1979@126.com, b lchenghao@126.com, c hnaibao@163.com Keywords: LiBr; carbon steel; corrosion inhibitor Abstract.
Luo, Electronic band structure of passive film on X70 pipeline steel, Electrochim.
Muller, Chemical composition and electronic structure of passive films formed on Alloy 600 in acidic solution, Corros.

Structures are shown in Fig. 1.
Figure 1 Chemical Structure of Dioxins (Left) and Dibenzofuran (Right) In water, dioxins are persistent organic pollutants (POPs) have low solubility and volatility.
References [1] H Fiedler, O Hutzinger, and CW Timms, “Dioxins: Sources of Environmental Load and Human Exposure”, Toxicological & Environmental Chemistry, vol. 29, 1990, pp. 157-234

The Ci and the phase angle can be measured by impedance spectroscopy on an ITO/SiO2/ITO sandwiched structure in the frequency range from 1.0 MHz to 1.0 Hz.
When a electric voltage is applied in an ITO /SiO2 /ITO sandwiched structure, protons in SiO2 proton conducting films move towards to gate dielectric / gate electrode interface to form an EDLC.
Wan: Journal of Materials Chemistry C, vol. 1 (2013), p.2781 [18] G.

Experimental Commercially available YSZ containing 8mol% Y2O3 (AR, TZ-8YS,~50nm, Jcc, Shenzhen, China) and NiO (CP, Aladdin chemistry Co.
Considering the pore inter-connectivity and pore structure, activated carbon is the best choice as pore-forming agent for Ni/YSZ anode.
[2] Ayhan Sarikaya, Vladimir Petrovsky, Fatih Dogan, Development of the anode pore structure and its effects on the performance of solid oxide fuel cells, Int J Hydrogen Energy.38(2013)1081-1091

Dry clay acts as insulator while wet clay provide electrical path due to broken bonds in its structure.
Figure 8 Porosity for different sand sample Detail grain size and structure of the sand samples were captured using polarized light microscope as figure 9 to 12.
Instrumental characterization of clay by XRF, XRD and FTIR.Department of Chemistry, Govt.

Concern about environmental issues and public pressure has made difficulty to license areas for the construction of new dams, or even to increase existing dams [8], which require constant monitoring and maintenance due to the high risk of occurrence of environmental disasters that this type of structure has.
The analysis of sample’s chemistry was provided by the mining company Vallourec.
Fig. 1: Particle size distribution of Portland cement and iron ore tailing Fig. 2: Image of the sample of iron ore tailings (A) and Portland cement (B) The SEM image shows the presence of compact particles, without lamellar structures, which could indicate a low specific surface area, in the sample of IOT.