Search results

Materials Science and Engineering, 6 (1970) 213–247
Journal of Materials Processing Technology, 210 (2010) 159–165
Journal of Materials Science and Technology, 23 (2007)289–300
Journal of Materials Science and Technology, 23 (2007) 47–54
Journal of Materials Science, 35 (2000) 1641–1659

Three different types of motion between the journal and bearing can be observed during the dynamics of the revolute joint clearance, namely, (1) free flight mode, in which the journal moves freely within the bearings boundaries, that is, the journal and the bearing joint are not in contact; (2) impact mode, which occurs at the termination of the free flight mode, being impact forces applied to and removed from the system; (3) permanent contact, in which contact is always maintained although the relative penetration depth between the bearing and journal varies along the circumference of the journal [5].
The journal radius of crosshead pin is 35 mm while the initial bearing radius of connecting rod is 35.1 mm.
The materials in contact have the properties of steel with Young’s modulus 2.06×1011 N/m2, Poisson’s ratio 0.3 and zero friction is assumed.
Fig. 5a depicts the journal center path of the joint with clearance.
Acknowledgements The research work presented in this paper was supported by Science and Technology Research Project of Heilongjiang Department of Education: Vibration Signal Analysis and State Assessment for Large Scale Reciprocating Compressor (Project number: 12521051).

It allows simulations of multi-material interaction problem without the need of a special contact algorithm.
The size of water is 100x100 cm. 40 000 material point are deployed uniformly in the problem domain.
Journal of university of science and technology of China Vol.37 (2007), pp.1306-1311
Chinses journal of high pressure physics Vol.25(2011),pp.165-172
A particle method for history -dependent materials.

Journal of Hazardous Materials, 306 (2016), 203-209
Journal of Hazardous Materials, 179 (2010), 160-165
Journal of Hazardous Materials, 102 (2003), 257-275
Journal of Hazardous Materials, 181 (2010), 700-707
Journal of Materials Science & Technology, 34 (2018), 1638-1651

And the physical parameters and material fracture parameters can be get from the literature of science and technology [7].
Pan The influence of tool flank wear on residual stresses induced by milling aluminum alloy Journal of Materials Processing Technology 209 (2009) 4502–4508 [2] J.C.
Journal of Materials Processing Technology 97 (2000) 200~210 [4] Z.T.
Ai The influence of tool flank wear on residual stresses induced by milling aluminum alloy .Journal of Materials Processing Technology 209 (2009) 4502–4508 [5] Mohamed N.A.
Journal of Harbin Institute of Technology.

Experimental Raw materials.
The chemical compositions of the main raw materials were shown in table 1.
As one of the most important parameters of lightweight materials, reheating linear change rate determines the overall thermal stability of materials.
Wang, Refractory Materials Technology.
Journal of Materials and Metallurgy.

Understanding the behavior of composite materials with such properties is essential for structural design.
Nowadays computational simulations play important role in the design process of such materials.
Dudinský: Computational Modelling of Composite Materials Reinforced by Glass Fibers.
IMA Journal Numerical Analysis Vol. 9 (1989), p. 231-242
Murčinková: MFS for modeling of inhomogeneous materials with large aspect ratio reinforcing elements.European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2012) , edited by J.

Acknowledgement I acknowledge the support by DST, Ministry of science and Technology (Govt. of INDIA) to carry out research work in the field of metaullrgy on the topics of implant materials.
Grande,M.Rosso,Properties of duplex stainless steels made by powder metallurgy,Archives of Materials Science and Engineering, (2007)
Rrack, Tittanium alloys in total joint replacement-A materials science perspective.
Titanium powder sintering for preparation of a porous functionally graded material designed for orthopedic implant[j],journal of material science, materials in medicine,2001, 225-231
Material Science and Engineering, (2013).

The data used in this study are academic papers that are published in Science Citation Index (SCI) journals.
Among journals that contained the papers, the top 10 journals in terms of the number of papers were reviewed by the researchers, and the following two journals were selected: ‘Solar Energy Materials & Solar Cells’ and ‘Solar Energy.’
One of the unique details in this study it that both journals the Solar Energy Materials & Solar Cells and Solar Energy that have become the population of research data, showing a great deal of difference in terms of research subjects.
Result of subject classification by text categorization Journal Cell Module/ Array System Relative/ Advanced Total Solar Energy Materials & Solar Cells 1,173 82 21 18 1,294 Solar Energy 104 15 69 549 737 Total 1,277 97 90 567 2,031 It was found that the published number of papers changed in similar patterns in all 4 major subjects as shown in Fig. 2.
It is hound that subject related to Dye-Sensitized Solar Cell material (DSC/DSSC), organic material (PPV), transparent electrode material (ITO) and Polycrystalline Si (which is a common solar cell material) were most active within the major Cell subject.

Soroushian Journal of Applied Polymer Science, vol. 131, no. 16, p. 40620, 2014
Vilatela Journal of Materials Chemistry A, vol. 2, p. 3881, Feb. 2014
Sun Materials & Design, vol. 94, pp. 295-302, 2016
Xu Dental Materials, vol. 32, no. 2, pp. 294-304, 2016
Bond Journal of Intelligent Material Systems and Structures, vol. 25, no. 1, pp. 87-97, 2013