Search results

Electrode materials of the NTP reactors can be selected to catalyse the treatment process; for example, silver electrodes can assist in pathogen inactivation since silver is known to have anti-microbial properties [11].
Experimental Section 2.1 Materials and setup A point-to-plane electrode configuration was used in discharge reactor for the experiments in this study (Fig. 1).
Materials,12 (2019) 2751
The European Physical Journal D, 72 (2018) 217
Journal of Hazardous Materials, 94 (2002) 89-99

The comparison tests were performed for optical properties of the materials.
“Innovative mechanical engineering technologies, equipment, materials 2015.
Series: Materials Science and Engineering 240 (2017) 012014
Series: Journal of Physics: Conf.
Series: Materials Science and Engineering 240 (2017) 012017

Pb(Zr0.53Ti0.47) O3(PZT) thin films are considered to be the most promising materials in micro-sensors and micro-actuators when current signal and force outputs are demanded.
Then heat treatment was performed with a rapid thermal process (RTP) at 400°C for 5 min to pyrolyze the organic materials.
Combined with the micromachining processes, the PSZT thin films are shown to be good candidate materials for developing the application of micro-force sensors.
Acknowledge This project was supported by the National Natural Science Foundation of China (No. 90607002) and Natural Science Foundation of Liaoning Province (No. 20082169).
Journal of the European Ceramic Society, 2002 ,22, pp. 209-218

Mukashev, IOP Conference Series: Materials Science and Engineering, 81 (2015) 012022
Otabaeva, Journal of Physics: Conference Series 1889 (2021) 022063
Otaboev, Inorganic Materials: Applied Research. 11 (2020) 503-506
Khazan, Funktional materials, 3 (1996)12-25
Otaboev, Surface e-Journal of Surface Science and Nanotechnology. 18, (2020)164-167

To clarify the conditions leading to final fracture in isotropic materials[5-7] and anisotropic materials (single crystals)[8-13], computational void growth and coalescence studies employed mainly unit cell models.
Lu, Modelling and Simulation in Materials Science and Engineering, 2005. 13(6): p. 875
Yue, Computational Materials Science, 2010. 48(3): p. 597
Needleman, Modelling and Simulation in Materials Science and Engineering, 2012. 20(3)
Yue, Materials Science and Engineering A, 2009. 520(1-2): p. 1

Dunn and Walter [3] have reviewed its occurrence in a wide variety of materials.
If this is possible, materials that are weakened due to abnormal grain growth can be considerably improved by addition of second-phase particles.
Materials Science Forum, 408 (2002), p. 949
Journal of Materials Science, 32(22) (1997), p. 5985
Materials Science Forum, Vols 467-470 (2004), p. 611

Introduction It is well known that in many materials crack propagation is accompanied by the formation of a damage surrounding the crack tip.
Takemori, Polymers Engineering Sciences, 22 (1982) 937-945
Chabaat, International Journal of Fracture, 37 (1988) 47-54
Lo, Journal of Applied Mechanics, 45 (1978) 797-802
Rubinstein, International Journal of Fracture, 27 (1985) 113-119

Years of theoretical research and production practice shows that the people for deepening understanding of landslide hazards, and always build in engineering, geology, rock mechanics, soil mechanics and a series of evolving branch of science[3], development and continuous improvement basis.
The strength of rock and soil targets c ,φ values ​​at the same time divided by a reduction coefficient, to get a new set of ć, φ́ value, and then as a new material parameters into the finite element spreadsheet, when the slope of the critical line given destruction of the state to determine the conditions, the correspondingis called the slope safety factor.
ABAQUS is the most advanced large-scale international generic non-linear finite element analysis software, one of its strengths is to calculate a variety of materials, processes, and changes in exposure to complex loading conditions of nonlinear combinatorial problems, a powerful post-processing functions.
Reference [1] Y.B.Du,G.Zheng and L.W.Jiang:Journal of Geomechanics Vol.16(2010),p.108 [2] H.D.Liu,C.L.Mao and Y.P.Guan:Journal of Water Resources Architectural Engineering Vol.8(2010),p.101 [3] S.M.Chong,Y.Y.Yu and D.A.Zhao:Journal of Heilongjiang Institute of Technology Vol.23(2009),p.24 [4] S.R.Wang,X.Wei and M.C.He:Journal of Mining & Safety Engineering Vol.26(2009),p.277 [5] C.Xu,Y.Q.Li and R.B.Jiang:Geotechnical Engineering Technique Vol.22(2008),p.71

Journal of hydrology, 1997. 196(1-4): p. 204-229
Journal of hazardous materials, 2009. 164(2): p. 1257-1265
Journal of Hydro-environment Research, 2013
Forest Science, 1989. 33((2)): p. 453-468
Journal of Transport Geography, 2007. 15(5): p. 396-406.

Analysis on the Structural Prototype with Finite Element Model Material Constitutive Model.
Chinese Journal of Geotechnical Engineering,1998,20(1):112–113
Journal of Qingdao Technological University,2006,27(4):l-5
Journal of Xi’an University of Science and Technology，2007，27（1）：39-42
Journal of Xiangtan University of Mining,2003,18(3):60-64