Search results

Table 1: Test parameters for the wear studies General Settings glide speed: 0,45 ms contact area: 112,5 mm2 normal force: 25 N contact pressure: 0,22 MPa PTFE-Compounds density (gcm3) shore hardness (D) ball indentation hardness (Nmm2) pure PTFE 2,17 ± 0,05 62 25,3 PTFE-glass fibre 2,25 64 32,2 PTFE-carbon-graphite 2,13 ± 0,03 64 ± 3 39,9 PTFE-bronze 40% 3,22 ± 0,04 68 ± 2 44,1 counter running surface: 1.2842 (90MnCrV8); as-supplied hardness: 229 HB longitudinal twist-free grounded Rz = 0.537 µm Ra = 0,0725 µm transversely grounded to the run direction, twist 90° Rz = 1,26 µm Ra = 0,17 µm shot-blasted isotropic surface Rz = 7,00 µm Ra = 1,04 µm milled surface with directed twist Rz = 5,24 µm Ra = 0,786µm Discussion and Data Analysis The mass of the samples has been determined gravimetrically before and after the experiments with a semi-microbalance (reproducibility: 0.015mg).
At least a reduction of the possible effect of funding active structures can also be expected.

Up to a maximum load of crack opening the resistance increases (in contrast of its reduction for the sample without crack).
Reactance of predicted and measured EMI as function of tensile load It can be seen that the predicted magnitude and reactance are close to the test data.

Once this data is available, single front welding processes as well as two front processes can be optimized.
Schulze, Targeted Weld Seam Formation and Energy Reduction at Magnetic Pulse Welding (MPW), eBIS 2017 (2017) 91–102

A comparison of the laboratory test results with the actual lifespan of the refractories in metallurgical equipment has shown that the calculations match the factual data.
Yi, Corrosion resistance of high-alumina graphite-containing refractories to melts during reduction melting, Refractories and technical ceramics. 10 (2007) 37-41

This is in well agreement with the results from the microtensile tests, i.e. a significant reduction in the value of modulus for the CNT containing samples compared to the reference one.
Note that the scale for the pure copper REF2-ABC is on the right side of the graph while the scale for the reinforced materials is on the left The method for measuring the thermal conductivity turned out to be reliable and accurate, as the thermal conductivity of the reference sample REF2-ABC at room temperature was estimated to be 403 W/mK (Fig. 5) and which corresponds quite well with data from literature for pure copper.

The goodness-of-fit model with experimental data was confirmed by the correlation coefficient (R2).
Nazockdast, Reduction of noise from disc brake system using composite friction materials containing thermoplastic elastomers, Appl.

The tests were carried out at 750 °C for two different height reductions namely 30 % and 50 % with a constant speed of 0.1 s-1 and 10 s-1.
The software system FORGE® NXT 1.0 was used to model the forming process with the implemented material data.

Since resin absorbs water by aging in high temperature and high humidity conditions, the reduction in the peak strength at 1296 cm-1 seems to be caused by water absorption reaction.
Furthermore, dispersion of plotted data was seen in the relationship between Dw and the tensile strength in the latter period in aging at the temperature over Tg.

Pulse electroplating of Zn–Fe coatings resulted in the grain size reduction to 50 nm at Jp 0.2 A cm-2.
XRD spectra for Zn-Fe alloy coatings by PC deposition J-60-9 and by RPC deposition J-60-9(30:8) The influence of pulse parameters on the phase composition of the deposited alloys can be determined from XRD data.

Relevant data show that the number of newly started highway projects in our country reached 111 in the first half of 2009, with the construction mileage reached 12 000 km and the total investment will reach about 700 billion Yuan.
Effects of Geosynthetics on Reduction of Reflection Cracking in Asphalt Overlays[J].