Search results

Baali, et al., The hydrogeochemical characterization of Morsott-El Aouinet aquifer, Northeastern Algeria.
Ptacek, et al..
Brooks, et al..

Sun et al [4]developed a method with the oxidation of the ozonide with molecular oxygen as the second step, supported by Mo-, V-, Mn-, Co-, Fe-, and Pb-containing oxides or salts and tungstic acid as oxidation catalysts which can give AA in range from 70 to 87% [5].
Carlson , E.L.
[4] Z.Sun ,Y.Zhang ,et al , Zhongguo Youzhi.
Marcy et al:Chem Mater.

Sweet potato starch was isolated by following the method of Sandhu et al [5].
The sweet potato starch was phosphorylated by using the method described by Sitohy et al [1]with slight modification.
The starch digestibility was determined according to the method of Goni et al [6].
S.M., El-Saadany.

Introduction Al-based and Fe-based salts are widely used inorganic coagulant in water treatment.
However, the residual Al in finished water has accumulation harm to human body and animal tissue [1].
The average Zeta potential of PFA (Al concentration of 0.09 mol.L-1) was 36.1 mV.
References [1] E.L.

Abdel-Hady et al. prepared the membrane in this way.The membranes achieve better water uptake, ion exchange capacity, AC electrical conductivity and tensile strength compared to that of Nafion-112[12]. 3.3 Cross-linked membrane Cross-linking can hinder the mobility of the polymer chains and efficiently enhance the mechanical strength by limiting the high degree of water uptake[13].The cross-linked membranes displayed somewhat lower proton conductivities than the corresponding uncross-linked ones because of the reduced IECs of the former.
Ren et al. fabricate the cross-linking Am-SPAES/SiO2 hybrid membranes,and the performance of the hybrid membranes containing cross-linking network structure was considerably improved[14].Luo et al. prepare a double cross-linked membrane.The second cross-linking significantly decreased the water uptake of the membrane.
[12] E.E.Abdel-Hadya,M.M.El-Toonyb,M.O.Abdel-Hameda:Graftingof glycidyl methacrylate/ styrene onto polyvinyldine fluoridemembranes for proton exchange fuel cell.Electrochimica Acta,103(2013),p.32-37

.,1911.126,124C [8] N.B.Brandt and N.I.Ginzburg,Contemporary, Phys.10(1969)355 [9] R.H.Parmenter.Phys Rev.166(1968)392 [10] O.Ershov et al.
Quan et al., Solid Stlid State Commum 65(1988)869 [36] B.V Vasiliev V.I Lushchikov and V.V Sikolenko JETP Lett 47 (1988) 334 [37] M.K.Crawford M.N.Kunchur W.E Farneth et all., Phys Rev B 41 (1990) 282 [38] Y.
Zhernov, el al, Physica C 272 (1996)257 [40] J.

References [1] Todd Austin, E.L., Dan Ernst.
Hallnor et al.
[4] Vachharajani, M., et al..Microarchitectural Exploration with Liberty.
[5] Bohrer, P., et al..

Effect the temperature on work adhesion in Al-C composite.
Zhengang Liu at el. investigate the influence of Mg addition on graphite particle distribution in the Aluminum alloy matrix composites.
Al-Ti-C system show that titanium carbide (TiC) was formed in the system.
Silicon has tendency to reduce aluminium carbide formation in C/Al–Si composites.
Fluidity of binary Al-Si alloys, at constant pouring temperature (800°C)

This validation was conducted by comparing the obtained numerical results with experimental published in the study by Huang et al. [50].
The temperature values obtained from the simulation show good agreement with the experimental values reported by Huang et al. [50].
In the same vein, Tripathi et al
Al-Salaymeh, Temperature Effect on Performance of Different Solar Cell Technologies.
Bria et al, B.

Effect of Mn-Content on the deformation behavior of binary Ti-Mn alloys Mohamed Kamal Gouda1, a *, Koichi Nakamura 1, 2, b and Mohamed Abdel-Hady Gepreel1,c 1Materials Science and Engineering Department, Egypt-Japan University of Science and Technology, Borg El Arab, Alexandria 21934, Egypt. 2Center for the Promotion of Interdisciplinary Education and Research, Kyoto University, Kyoto 615-8540, Japan.
The cold workability of titanium alloys was studied in many previous research, for example Wang et al. studied the cold workability dependence on the phase stability for Ti-Nb-Ta-Zrβ-titanium alloys [8].
Also, Takemoto et al. investigated the effect of Mo-content on the cold workability in binary Ti-Mo β-titanium alloys [15].
El Moniem, A study on phases change of Ti-Mn alloys produced by metal injection molding, AIP Conference Proceedings 1569 (2013) 203-207