Search results

Meanwhile, biodegradation acts like a catalyze for the reduction process that is found biologically in terms of chemical compounds’ complexity [3].
However, the bacterial biomass did not change either (data not shown) when using the powdered bioplastics.

However, although pin connection has a large number of applications in China, there are few specifications prescribed on this type of connections, and the experimental and analytical study data are limited[9].
When Specimen JD3 reached the ultimate load, the carrying capacity had little reduction.

., then transformed into data processed by the 3D printers [2].
This phenomenon is known as the plasticization effect by reduction of interactions between polymeric chains [9,12].

SEM (scanning electron microscope) analysis of the AA2124/SiC/25p-T4 MMC showing: (a) base MMC, (b) weld zone [2] Regarding the microstructure of the composite materials with metallic matrix the following can be said: a better homogenization of the initial distribution of abrasive particles occurs, irrespective of rotational speed of particles type in FSW zone [6], [1], [2], [7], [14], particles were distributed more homogeneously in the WZ compared to those in the BM [7], the abrasive effect of the pin on the ceramic reinforcement led to a significant reduction of the size particles to the base MMC [12], [2], [3], [10] and grain refinement of the matrix aluminium alloy was observed [12].
A comparison of the tensile data and the microhardness profiles reveals the tendency of UTS corresponding very well with the tendency of hardness minima, which demonstrates the precipitate evolution caused by FSW thermal cycle determines both the microhardness distribution and tensile property of the joints [17].

Pretreatments such as chlorination, oxidation, reduction, chemical processing, and organic solvent pretreatments are usually necessary to increase the reacting efficiency of protease, due to unavailability or lacking of specific and efficient proteases.
The wool fiber samples were tested for tenacity and extension @ break on the Single Fiber Tenacity Tester (Type YM-06A) at 10mm gauge and 10mm/min test rate, after balanced for 24h under the standard atmosphere condition of temperature(20±2 oC and RH(65±3%). 100 fiber specimens were randomly sampled and measured for averaged data.

Chemical and physical properties of nanosilica used in the research (developed on the basis of the material safety data sheet) SiO2 content min 99.8% Surface area 170±30 [m2/g] Bulk density 50 [g/l] pH, (4% aqueous dispersion) 3.5 – 5.5 Weight loss on ignition (2 h in 1000oC) 2.0% Weight loss after drying (2 h in 105oC) 0.6% Microsilica was used as microfiller.
Hosseini, Reduction of Cement Consumption by the Aid of Silica Nano-Particles (Investigation on Concrete Properties).

Isothermal holding for 30s after hot-rolling with final pass reduction 20% (equal true strain 0.23), causes that the fraction of statically and metadynamically recrystallized grains occurs in about 30% and is considerably lower than for specimens after hot-working in the Gleeble 3800 simulator.
· It was concluded on the basis of the own investigations [15-23] that mechanical properties of high-manganese austenitic steels in the condition after supersaturation state and on the basis of data from the literature that the examined steel subjected to thermo-mechanical processing are characterised by a yield point higher by approx. 200-250MPa, which is a result of precipitation strengthening of such steels by the dispersive particles of Nb and Ti carbonitrides and is also connected with thermo-mechanical treatment employed

To deposit Pt / or Ru precursors onto functionalized MWCNT, 0.1g of MWCNT was immersed in 2.0 mL of 0.05M H2PtCl6·6H2O (99.9% Alfa-Aesar)/or 2.0 mL of 0.05M RuCl3·6H2O (99% Alfa-Aesar) aqueous solution with 40 mL of ethylene glycol (99.8% Sigma-Aldrich). 0.4M NaBH4 was added drop by drop, to the mixtures with vigorous stirring for the complete reduction of Pt/or Ru form their respective metal salts.
These binding energy values are in good agreement with the literature data for Pt.

According to the literature data [10] the low water resistance of gypsum binders is explained by the high solubility of calcium sulfate dihydrate, which amounts to 2.04 g/dm3 CaSO4 at 20°С, its high permeability and the wedging action of water molecules at their penetration into intercrystalline spaces (Rehbinder effect).
At the same time the reduction of W/G requires adding plasticizing admixtures to provide the necessary flowability of the mix for the moulding technology or passing from conventional moulding methods to using harsher moulding mixtures and compressing technologies.

Photons, with a higher transmitting speed, a larger data conveying ability, and a lower interaction with each other, are believed to play a key role in next-generation information technology [1].
This can afford a significant reduction in aspects such as device dimension, cost, package complexity, light coupling, and power consumption.