Search results

Two component nanocomposites of polymer containing 3d transition metal clusters are of immense interest because of their potential future applications in magnetic high frequency or data storage media, in particular.
These composites, with appropriate magnetic volume, are promising candidates for magnetic high frequency or data storage applications [2], such as low loss tunable microwave devices [3] or microinductors [4].
Normally in such cases, reduction of a metal salt [9] is needed in order to avoid metal oxide formation.

Then, the coupling program transfers the temperature data to the mechanical solver.
The other geometry data are given in the inlet.
The material data used for the simulations are summarized in Table 2.
The experimental data are also plotted in Fig. 19.
To describe experimental data, δ is interpreted as the twinning stress.

The data of the real RDN are in Appendix B, the sketched SLD is shown in Fig. 6, and results of |V| in p.u are shown in Fig. 7.
Load Data Bus no.
Load Data Bus no.
Line Data Bus no.
Line Data Bus no.

Data Analysis Data obtained on an ordinal scale are grouped based on the p53, hTERT, and grading immuno-expression distribution patterns.
Analysis of data using Excel-MegaStat with a significance of p <0.05 (95%).43 5.
Research Data on SCC Patients.
Sample data number 11 to 20 which are SCC with moderate differentiation showed varying assessment scores as well as on well differentiated SCC.
Based on the research data it can be seen that samples number 21 and 28 have the best prognosis compared to the others.

In order to fit the data of impedance spectra, proper equivalent circuits were employed.
During the first 4 months, Ecorr reduces gradually mainly due to the depletion of oxygen in the cover zone of cement-based materials; However, in the following 2 months, Ecorr reduces rapidly for reason of breakdown of steel passive film; Finally, after 6 months of exposure, no obvious reduction in potential is observed for all specimens which accounting for the appearance of stable active corrosion of steel (Ecorr < -276mVSCE) according to ASTM-C876 [13].
To simulate the data of electrochemical impedance spectra, an appropriate equivalent circuit (EC) is commonly applied via electrical fitting.

Even 20% blending leads to strength increase at a w/b-ratio of 0.32 Fig. 5 presents data from the computer simulation study.
Obviously, physical strength contributions due to denser packing compensated for the reduction in chemical contributions.
Results and Discussion Overall data on porosity and connected (percolated) fraction of porosity at the same ultimate degree of hydration (DOH) are given in Table 2.

., the slope of the ∆G curve becomes 0, and the formula for the critical nucleation radius can be obtained as follows: if d∆Gdr=4πrg2γ+rg∆gvva=0 (2) rc = rg =-2γva∆gv (3) When the size of the crystal nucleus does not reach the critical nucleation radius, the crystal nucleus tends to reduce its free energy by reducing its volume, and the smaller the crystal nucleus size, the higher is the probability of volume reduction.
The data were captured from the initial state at room temperature.
[4] A.Stukowski, Visualization and analysis of atomistic simulation data with OVITO–the Open Visualization Tool, Mater.

This reduction in sample size occurred due to some samples succumbing to fungal infestation (the fieldwork lasted for 45 days), leading to their exclusion from the samples selection process to prevent any potential bias in the models.
Analysis of wood specific gravity radial variability Once the best performing model was chosen, it was used on the acquired spectral data.
Chagnon, Comparison of selection methods of explanatory variables in PLS regression with application to manufacturing process data, Chemom.

The application of 2099-T8511 extrusion products in the floor structure of A380 aircraft has achieved weight reduction successfully[3].
The data indicate that the tensile properties in the same thickness layer are anisotropic.
These data indicate that the rate of the Taylor factor change with position through the thickness agreed with the rate of the longitudinal yield strength change, which is in accordance with experimental observations from the literature[17-18].

The results indicate that when using the same JENDL-3.3 cross-section data library both codes give similar results, the difference being mostly due to the use of slightly different tallying surfaces in MCNPX and GEANT4.
The thickness of the HIPOS concept moderator was adjusted such that 50 % of the positrons would pass through the tungsten foil converter/moderator with an adequate reduction of their energy.
It showed a rather good agreement of the calculated values with the measured data (better than 5 % agreement).