Search results

But by the 90 s, Russia has been able to take advantage of Hydro forming technology to shape lower plastic materials such as titanium alloy and high-strength steel [2].
On other media of research, Henan Science and Technology University had "elastic-plastic force transmission media analysis of three pipes under axial compression expansion technology" [4],Polyurethane rubber-elastic materials, including wax, graphite mixed plastic materials transfer medium, and respectively started technology testing in copper T-shaped tube and hard aluminum T-shaped tube subjected to axial compression bulging, analysis the effects of different transfer mediums on bulge forming process, but the results of their experiment is elasticity of polyurethane rubber material used for bulging falls short of height to diameter ratio greater than 1 of support pipes.
Henan: Henan University of science and technology, 2004.
In Chinese [4] Mustafa Ahmetoglu,Jiang Hua,Srikanth Kulukuru,Taylan Altan.Hydroforming of Sheet Metal Using a Viscous Pressure Medium.Journal of Materials Processing Technology,2004,146:97～107 [5] Mingwang Fu, Shiqiang Lu, Maoheng Huang.
Journal of plastic engineering, 1999,L6 (3): 46~48.

Introduction The similarity of synthetic hydroxyapatite (Ca10(PO4)6(OH)2, HA) to bone mineral has led to extensive use of HA in materials science and medical fields, especially as a bone substitute material because of its high biocompatibility and osteo-conductivity [1-3].
The limits for its validity differ for different materials.
Lin: Materials Letters Vol. 57 (2002), p. 858 [4] Y.
Fukumori: Materials Science and Engineering B Vol. 148 (2008), p. 162 [5] S.
Rey: Materials Research Bulletin, Vol. 34(1999), p.2279 [13] K.

China 201804 (Corresponding author) 3Institute of Geology and Geophysics, China Academy of Sciences, 19 Bei Tu Cheng Xi Lu Chaoyang District, Beijing P.R.
Introduction The asphalt pavement design method based on elastic layered system reflects the mechanical response of pavement structure to some extent, but due to the complexity and variability of materials’ composition and nature, the impact randomness of environment and load factors, and the quality instability of non-factory construction, it is very difficult for the purely mechanical method to learn the real response of actual pavement structure.
So the surface materials need more attention on fatigue performance especially for the top two layers
Acknowledgments The research was supported by the National Natural Science Foundation of China (No. 50968016).
[3] Xudong Zha, Qisen Zhang: China Civil Engineering Journal Vol. 33(5) (2000), p. 92~96, in Chinese

And studies on organic waste water treatment[2-5], biomass pyrolysis[6-10] and high polymer materials degradation[11-14] in supercritical water has been carried out scientifically.
The Journal of hazardous materials, 2009,163(2-3):1142-1147
Chemical Engineering Journal,2008,137(3):542-549
The Journal of supercritical fluids, 2012,72:120-124
[11]Linghui Meng, Yudong Huang, Yan Zhang.Materials science ＆technology,2003,11(3)：311-314(In Chinese)

Introduction Carbon materials are unique and versatile in their performance.
Activated carbon materials are effective in removing pollutants (both gaseous and liquid).
In addition carbon materials are resistant to corrosive(acidic and basic) and toxic environments.
Nanostructured materials. - Moscow: The Academy, 2005.
Some Applications of Nanocarbon Materials for Novel Devices / / R.

Materials The work in this paper was based on previous studies [1,2].
The formulated fluid consists of materials, which are considered biodegradable such as natural polymers.
In the drilling fluid formulation, all raw materials were mixed with distilled water.
All the raw materials were varied at four different concentrations to study their effects on the fluid density.
Starch-composition, fine structure and architecture, Journal of Cereal Science 39 (2004) 151-165

Theoretical and Experimental Studies on Strength and Stiffness of Vacuum Glazing Xiaogen Liu1,a, Yiwang Bao2,b State Key Laboratory of Green Building Materials, China Building Materials Academy, Beijing 100024, China axtlxg88@163.com, bbyw@ctc.ac.cn Keywords: vacuum glazing; strength; stiffness; equivalent thickness Abstract.
Materials Science and Engineering (B),Vol.138(2007).P. 128-134
Construction and Building Materials,23(2009).P. 1378–1388
Stresses in Vacuum Glazing Fabricated at Low Temperature.Solar Energy Materials & Solar Cells,91(2007).P. 290–303
Journal of Zhengzhou University Engineering Science,30(2009).P. 101-105

Effect of gallium doping on the properties of GZO target Liu Cunqi1, a, Cai Xuexian1,b, Zhang Zhongjian2,c, Gao Ling1,d, Xiao Chao1,e, Shang Fuliang1,f, Yang Haitao1*, 1Key Laboratory of Functional Materials of Shenzhen, Shenzhen Engineering Laboratory of Advanced Technology for Ceramics Processing , College of Materials Science and Engineering, Shenzhen University, Shenzhen 518060, China 2State key Laboratory of Cemented Carbide, Suzhou Cemented Carbide Industry Company, Suzhou, 412000, China acunqiliu@163.com, b xh.xue@qq.com, ＊Corresponding author yanght63@hotmail.com Keywords: Ga2O3 content; air sintering; GZO targets Abstract.
However, the usage of ITO is limited as high cost, rare and poisonous element (Indium), and unstable in hydrogen plasma materials In2O3[3, 4].
Therefore, GZO targets with excellent mechanical properties, high density, and low resistivity become the key materials for making uniform and controllable composition.
Science 1995: 270: 1789–1791
Materials Science and Engineering 2012: B 177: 1777– 1782

Ball, Performance of structural concrete with recycled plastic waste as a partial replacement for sand, Construction and Building Materials. 161 (2018) 63–69
Construction and Building Materials. 197 (2019) 734–746
Mater Science. 281(1987) 22-91
Yue, Effect on mechanical properties of rubberized concrete due to pretreatment of waste tire rubber with NaOH, Applied Mechanics and Materials. 357-360 (2013) 897-904
Journal of Materials and Engineering Structures (JMES). 7 (2020) 57-72

Al-Kayiem, Journal of Applied Science Vol. 12 (23) (2012) 2338-2345
Yoshid, Journal of Heat Mass Transfer Vol. 41 (4-5) (1998) 709-718
Upadhyaya, Science of Sintering Vol. 42 (2010) 99-124
Di Blasi, Journal of Chemical Engineering Science Vol. 65 (2010) 4117–4133
Metaxas Time domain finite element analysis of multimode microwave applicators loaded with high and low loss materials, Proceeding of International Conference on Microwave and High Frequency Heating, Cambridge, UK, 1995