Search results

It is generally accepted that TiO2 can generate electron-cationic holes under illumination, which promotes oxidation and reduction reactions at the solid surface [7, 8].
The diffraction patterns (data not shown) also imply the formation of TiO2 nanostructures with good crystallinity.

However the possibility of reaching elongations higher than 200% can bring to significant cost saving benefits: in particular complex shape components can be manufactured without any joint with a weight reduction and an improvements of its mechanical behaviour [1].
Zhang: Material modelling data for superplastic forming optimization, Materials Science and Engineering A 410-411 (2005) 100-104

INTRODUCTION According to data from the statistics of the largest companies in the world and the only global non-governmental organization dealing with the management of secondary raw materials, the Bureau of International Recycling based in Brussels, secondary raw materials industry annually uses 700 - 800 million tons of secondary raw materials (i.e. more than 40 % of all materials used in industry) with an annual turnover of about 170 trillion $ [1].
§ Size reduction in high-speed forced-action mixers to polyurethane grain size of 6 mm.

The algorithms of this paper will discuss the difference in these two data structures.
We check the correctness of syntax and get the syntax tree using total control procedures of the LR analysis method by bottom-to-up reduction.

Better thermal insulation properties, which are achieved, among others, by increasing the air content in concrete mixtures (i.e. by increasing the porosity of the material, in particular under the condition of a relative reduction of material-thermal parameters and strength) are the desired properties of innovative types of light-weight concrete.
GUM: Evaluation of measurement data--Guide to the expression of uncertainty in measurement, Paris: BIPM.

In Fig. 3, a comparison between thermogravimetric analysis data (air) obtained for pure polymer and composites has been reported.
This weak bonding will not allow transferring stress efficiently leading to reduction in strength.

29 0 - 0 - 20 - 35 0 - 0 - 20 - 10 minutes 27 5,3±0,1 10,8 4,0±0,2 25,0 10,7±0,3 14,3 29 3,3±0,1 17,3 5,3±0,3 21,7 11,3±0,3 13,5 35 5,0±0,2 20,0 1,3±0,3 86,6 13,7±0,5 15,2 15 minutes 27 4,3±0,1 13,3 5,7±0,3 27,0 10,0±0,2 10,0 29 3,0±0 0 7,3±0,1 7,9 9,7±0,1 6,0 35 3,3±0,1 17,3 9,0±0,2 11,1 7,7±0,1 7,5 20 minutes 27 2,3±0,1 24,7 12,0±0,4 16,7 5,7±0,3 27,0 29 0,7±0,1 86,6 13,7±0,3 11,2 5,7±0,3 20,4 35 2,7±0,1 21,7 13,3±0,3 11,5 4,0±0,2 25,0 Shoots from the rootstock 5 minutes 27 1,7±0,3 91,6 1,7±0,1 34,6 16,7±0,5 11,8 29 0,7±0,1 86,6 1,7±0,1 34,6 17,7±0,3 17,5 35 1,0±0 0 1,7±0,3 91,7 17,3±0,3 8,8 10 minutes 27 9,7±0,1 6,0 3,7±0,1 15,7 6,3±0,1 9,1 29 8,7±0,1 6,7 4,3±0,1 13,3 6,7±0,1 8,7 35 7,0±0,2 14,3 4,0±0,2 25,0 9,0±0 0 15 minutes 27 6,3±0,1 9,1 8,0±0,2 12,5 5,3±0,1 10,8 29 5,7±0,1 10,1 7,7±0,1 7,5 6,3±0,1 9,1 35 5,3±0,1 10,8 7,3±0,1 7,9 7,7±0,1 7,5 20 minutes 27 2,0±0,2 50,0 14,7±0,1 3,9 3,3±0,1 17,3 29 1,0±0,0 0 15,3±0,1 3,7 2,7±0,1 21,7 35 1,3±0,1 43,3 15,7±0,1 3,7 1,7±0,1 34,6 The data
At the same time, increase the exposure in the range from 10 to 20 minutes leads to a reduction in the total amount of sterile explant morphogenic dying off due to not only the pathogenic microorganisms but the cells themselves, and plant tissue cells.

Among these, soil volume to weight was used an “S” type reduction function (Equation 1) and other soil factors was used an “S” type rise function (Equation 2).
Data analysis Employing single-factor ANOVA, we analyzed whether different land use modes had a significant effect (α= 0.05) on soil quality.

Structural engineers could use the data reported in this abacus for their calculations, avoiding any type of on-site investigation to assess the mechanical characteristics of the masonry material of the building under their analysis and consideration.
Figure 2 shows the panels’ response under lateral loading in terms of angular strain at Building B: it can be clearly noted that the combined reinforcement produced an high increment of both the lateral load capacity and shear stiffness, and a reduction of the deformation capacity. .

This resulted in reduction of corrosion rate thereby shifting the curve of cathodic polarization and anodic polarization to the direction of reduced values of corrosion current.
Chemical Data Collections. 17 (2018) 321-326