Search results

The automated fibre length analysis represents a significant advance, but the pure numbers can only be correctly evaluated by taking the recorded images into account.
Krenkel, Cost Effective Processing of CMC Composites by Melt Infiltration (LSI-Process), Ceramic Engineering and Science Proceedings 22 (3) (2001) 443–454
Renz, C/C-SiC Composites for Advanced Friction Systems, Adv.
Forum 825-826 (2015) 215–223

Breitung, High-entropy oxides: fundamental aspects and electrochemical properties, Advanced Materials, (2019) 1806236
Chen, The microstructures and electrical resistivity of (Al,Cr,Ti)FeCoNiOx high-entropy alloy oxide thin films, Advances in Materials Science and Engineering, 6 (2015)
Trofimov, The poly-substituted M-type hexaferrite crystals growth, Materials Science Forum, 946 (2019) 186-191.

Improved Controller Performance for Electromechanical Axes Holger SCHLEGEL1,a, Arvid HELLMICH1,b*, Kevin HIPP1,c, Johannes QUELLMALZ1,d, Reimund NEUGEBAUER1,e 1Technische Universitaet Chemnitz, Faculty of Mechanical Engineering, Professorship for Machine Tools and Forming Technology, Reichenhainer Str. 70, 09126 Chemnitz, Germany aholger.schlegel@mb.tu-chemnitz.de, barvid.hellmich@mb.tu-chemnitz.de, ckevin.hipp@mb.tu-chemnitz.de, djohannes.quellmalz@mb.tu-chemnitz.de, ewzm@mb.tu-chemnitz.de Keywords: electromechanical axis, industrial controller, identification, controller parametrization, simulation based optimization, control loop performance monitoring Abstract.
Friction parameters were measured in advance.
J.; Hägglund, T.: Advanced PID Control.
Schönherr, et al.: Assessing the Performance of Servo Drive Feedback Controls, 13th Mechatronics Forum, International Conference, Proceedings, Linz (Austria), 2012 [13] Bracale, A. et al.: On some spectrum estimation methods for analysis of nonstationary signals in power systems.

Bulging Deformation Prediction and Experimental Verification of Bonded Double-Layer Clad Cylinder in Rotating Compression Sen-Chi Weng1a, Bor-Lih Kuo1b, Gow-Yi Tzou2,c* 1Department of Mechanical Engineering, Cheng Shiu University,Kaohsiung 833, Taiwan 2Department of Electrical Engineering, Fortune Institute of Technology, Kaohsiung 831, Taiwan.
Engineering for Industry 66, 1975
Jin, Journal of Engineering Manufacture 215, 883, 2001
Tzou, Sergei Alexandrov, “An Upper Bound Solution for Upsetting of Two-Layer Cylinder”, Materials Science Forum Vols. 505-507, January 2006, pp.1303-1308
Tzou, Sergei Alexandrov, “An Upper Bound Solution for a Two-Layer Cylinder Subject to Compression and Twist”, Key Engineering Materials Vols. 345-346, 2007, pp. 37-40

Metallic hollow sphere structures (MHSS) form a new group of advanced composite materials characterised by accurate geometry reproduction leading to stable mechanical and physical properties.
The sintered Hollow Spheres will be deformed up to 90% of engineering strain while the adhesively bonded Hollow Spheres will be deformed up to 75% of engineering strain.
The reason for the lower displacement rate of the adhesively bonded HS is that the simulation time would become too large if the engineering strain should also reach 90%.
Fig. 7) is shown up to 75% of engineering strain.
Forum Vol. 553 (2007), p. 45

TMR-DQP process was designed as a potential route utilizable with industrial hot strip production enabling concomitant accomplishment of high strength with improved elongation as well as low temperature toughness in advanced high strength steels (AHSS).
Engineering stress-strain curves of TMR-DQP steels processed at TQ 225 °C.
Fig. 2 shows the corresponding engineering stress-strain curves of High-Al steel with two different levels of nitrogen content.
Engineering stress-strain curves of TMR-DQP High-Al steel with nitrogen content 0.001 and 0.003% processed at TQ 225 °C.
Sietsma, New low carbon Q&P steels containing film-like intercritical ferrite, Materials Science and Engineering A. 527 (2010) 6429–6439

Microstructure Evolution during Sintering of Aluminium in Nitrogen Tadeusz Pieczonkaa, Jan Kaziorb Cracow University of Technology, Institute of Material Engineering, Warszawska 24, 31-155 Krakow, Poland a tpieczonka@pk.edu.pl, b kazior@mech.pk.edu.pl Keywords: Aluminium sintering, Dimensional changes, Aluminium nitride, Liquid phase sintering Abstract.
Forum, Vols. 426-432 (2003), p. 107
Hall: Advances in Powder Metallurgy and Particulate Materials, Orlando, 2002, Vol. 13, p. 139
Hebda: Advances in Powder Metallurgy & Particulate Materials, MPIF, Washington 2008, Vol. 5, p. 25
Hebda: Advances in Powder Metallurgy & Particulate Materials, MPIF, Nashville 2012, Vol. 5, p. 1

Introduction Weight and cost reduction in civil aircrafts by replacing rivets by advanced welding techniques [1] has now been realized [2] for skin-stringer joints (T-joints).
Forum 242 (1997) 11-24 [2] W.
Raynaud: Aircraft Engineering and Aerospace Technology 73 (2001) 147-159 [4] P.
Andreani: Advances in Physics 34 (1985) 445473 [10] V.

Sinha, Materials Science and Engineering C, (2013)
Pohl, Fatigue and Fracture of Engineering Materials and Structures, 13 (1990) 563-578
Shanina, Advanced Engineering Materials, 10 (2008) 1083-1093
Berns, Materials Science and Engineering: A, 481-482 (2008) 707-712
Gavriljuk, Key Engineering Materials, 345-346 (2007) 421-424.

In the typical example modules, there are many demonstrations of engineering background and animations of structural members.
Using advanced multimedia technology, we can make the teaching activity more vividly, arouse the interests of students and keep them motivated, teach more contents in classroom and improve the quality of teaching.
The further work is to add more and better background knowledge of practical engineering to the website, and to expand the test module with more and better exercises for classroom and homework.
“Development and application of multimedia CAI courseware in engineering mechanics course,” Proc. 2nd International Workshop on Education Technology and Computer Science, ETCS 2010, IEEE Press, Mar. 2010, v2, pp. 500-503
“Engineering mechanics teaching website designing based on JSP,” in Chinese.