Search results

H: Materials Science & Engineering A Vol. 478 (2008), p. 119 [2] D.
P, et al: Journal of Materials Processing Technology Vol. 201 (2008), p. 51 [4] F.C.
P, et al: Journal of Materials Processing Technology Vol. 167 (2005), p. 73 [6] K.H.
C, et al: Journal of Materials Processing Technology Vol. 177 (2006), p. 469 [8] C.A.
L: Materials Chemistry and Physics Vol. 104 (2007) p. 293 [9] M.K.

Additive manufacturing has allowed for the development of a wide variety of prosthetics using different materials.
Materials and Methods Mechanical system.
In the Low Cost section, several materials were discussed; to verify these materials a series of Von Mises and Displacement simulations were conducted.
On the other hand, the remaining four materials have similar behaviors, however, PLA is the one that has the easiest to print which gives rigidity to the grip, other materials give similar results.
Thakur, "Experimental tensile strength analysis of ABS material through FDM technique," Materials Today: Proceedings, Sep. 2023.

After crushing the mixture, all the materials should be sieved and stored respectively, in order to restrict the variation of gradation.
TEMPERATURE CONTROL REQUIREMENTS OF THERMAL REGENERATION [℃] procedure Preheating phase of crumbles Before delivering New materials Recycled materials Paving temperature Temperature at the fan entrance Storage temperature of crumbles requirement 160~180 150~160 >150 >150 >150,<170 >140 Mixture design The quality of old asphalt materials is the foundation of the whole regeneration project.
Thus it is necessary to evaluate these raw materials.
The following experiment of sieve test (water washing) with raw materials is listed in Table 2.
Quantity of new asphalt materials was calculated according to the proportion and the content of asphalt in the scrap.

Abstract.Based on 75 cube specimens(100mm×100mm×100mm) of the super high early strength grouting material at elevated temperature,this paper describes the design of the high temperature test,compressive test and some relevant phenomena in testing,analyzes strength of the super high early strength grouting material at elevated temperature,and obtains the stress-temperature curves of the super high early strength grouting material at elevated temperature.By analyzing the staged characteristics of the curves,the regularity of the strength of the super high early strength grouting material at elevated temperature is discussed and some fitting mathematical formulas are suggested.
(a) 600˚C (b) 800˚C Fig.4 Comparison of destroyed specimens The stress-temperature curve.In order to facilitate comparison,draw the stress-temperature curves together and get stress-temperature curves of different materials at elevated temperature.Stress-temperature curve of every type of grouting material is as shown in Fig.5.
References [1] Railway Construction Academy of Railway Sciences Institute.
Railway Construction, 1977 (5) :6-13 [2] Zhang Xiaoping,Sun Changzheng,Zhao Tongfeng,Chen Qian.Study on Fire-resistance Performance Test of the Super Early Strength Grouting Material[J].Construction technology,2014, 43(5): 13-16 [3] Xiao Jianzhuang,Wang Ping,Xie Meng,Li Jie.Experimental Study on Compressive Relationship of HPC at Elevated Temperature[J].Journal of Tongji University, 2003, 31(2): 186-190 [4] Hu Yuefeng.
Journal of Building Materials, 2004, 7(3): 281-285

Witit-Anun4e 1Environmental Science Department, Burapha University, Thailand 2Human Resource Management Department, Burapha University Thailand 3Chemistry Science Department, Burapha University, Thailand 4Physics Department, Burapha University, Thailand apruethsan@gmail.com, bwanvicechanee@hotmail.com, cpichan@buu.ac.th, dpumipat@buu.ac.th, 4nirun@buu.ac.th *Corresponding Author Keywords: Construction Material sector, Forward Linkage, Real Benefit, Environment Cost, Carrying capacity Abstract.
Moreover, the National Economic and Social Development Board (2015) stated that firms did not consider the cost from natural resources materials, energy and transportation, fertilizer and pesticides, sanitary, and similar services, which represent environmental costs (2015).
The calculation uses input data categorized as natural resource materials, energy and transportation, fertilizer and pesticides, and sanitary and similar services.
Bradford, Taxing Variable Cost: Environmental Regulation as Industrial policy, Journal of Environmental Economics and Management. 4(May), (1996) 60
Hugo, Pistikopoulos, Environmentally conscious long-range planning and design of supply chain networks, Journal of Cleaner Production. 13(15) (2005) 1471-1491

But there are some deficiencies in the research about structure and materials of electrode preparation.
Experiment Main Materials.
Journal of Jiangsu University (Natural Science ), 2009.30 (2):129-133.
Journal of Jiangsu University (Natural Science), 2009, 30 (4): 366-369.
Journal of Jiangsu University(Natural Science), 2010,31(5): 558-563.

Key Engineering Materials, Vol. 455 (2011), pp.575-579
Advanced Materials Research, Vol. 887-888 (2014) No.1, pp.1215-1218
Applied Mechanics and Materials, Vol. 509 (2014) No.1, pp.50-55
Advanced Materials Research, Vol. 902 (2014) No.1, pp.129-134
International Journal of Mechanical Sciences, Vol.41(1999), pp.301-1322

Most of these materials has anisotropic coefficients of thermal expansion (CTE), resulting in a microcracking during cooling of the sintered material.
Umarji: Solid State Sciences Vol. 6 (2004), p. 1313
Hanuza: Optical Materials Vol. 34 (2012), p. 1048
Nikolov: Solid State Sciences Vol. 12 (2010), p. 2010
Harris: Journal Materials Science Vol. 47 (2012), p. 6286

Piezoelectric materials such as aluminium nitride (AlN) and zinc oxide (ZnO) are mainly used in the FBAR.
Ru is used as the electrode material for FBAR in K-band frequency due to its higher acoustic impedance than other electrode materials [1].
Pensala, "Thin Film Bulk Acoustic Wave Devices," PhD, School of Science, Aalto University, Finland, (2011)
Nguyen, "High-Q Hf Microelectromechanical Filters," IEEE Journal of Solid-State Circuits vol. 35, pp. 512-526, (2000)
Chowdhury, Dasgupta, S.P, "Compuation of Rayleigh Damping Coefficients for Large Systems," Electronic Journal of Geotechnical Engineering, vol. 8 C, (2003)

Because of this, amalgam filling materials continue to be used in some countries.
Journal of the Mechanical Behavior of Biomedical Materials. 91 (2019) 109–121
Journal of Dentistry. 130 (2023) 104409
Journal of the Mechanical Behavior of Biomedical Materials. 47 (2015) 65–76
Materials Science Forumю 1006 (2020) 253–258