Search results

Journal of Hazardous Materials 180,115-121
Journal of Hazardous Mat erials182, 656-664
Microchemical Journal 94, 99-107
Journal of Hazardous Materials 143, 511-515
Science of the Total Environment 408, 726-733

This property is mainly the result of either the chemical composition of materials or the geometric structures of the surface [6].
However, due to the complex processes and expensive materials used in these methods, a simple and cost effective alternative for fabricating large area, nano-scale periodic structures is in urgent need.
These processes are thus not suitable to fabricate simple two-dimensional nano-tip structures on surface of materials in large areas at a low cost.
Dill and ADJ Haymet, A view of the hydrophobic effect, The Journal of Physical Chemistry B 106 (2002) 521-533
Lee, and SRJ Brueck, Nanostructures and functional materials fabricated by interferometric lithography, Adv Mater 23 (2011) 147-179

The resin capsules have gone through nearly half a century's history as support materials in resin bolt support system [1-3].
High-quality polyester film and nylon film were used as packaging materials to enhance safety in use process.
High-strength and low relaxation prestressing steel strands of 22mm diameter and 1´19 shares were used as cable materials, and the length of cable was 4300mm with combined anchorage of resin capsules and cement.
Journal of Southeast University (Nature Science Edition) (in Chinese), 35(2005), Supp.1,p.49
Coal Science and Technology(in Chinese),25(1997),No.9,p.17.

Materials and methods Experimental diets The diet formula used in this experiment was shown in Fig. 1.
Hu: Fisheries Science.
Dong: Marine Environmental Science.
Yu: Fisheries Science.
Lu: Journal of Fishery Sciences of China.

Materials Stone Materials.
Dowel and Fixing Materials.
Dai: Three-Dimensional Micromechanical Finite-Element Network Model for Elastic Damage Behavior of Idealized Stone-Based Composite Materials, Journal of Eng.
Xu: FEM Analysis of Grinding Damage Mechanisms for Ceramics Materials, Materials Science Forum, Vol. 532 – 533 (2006), p. 432-435
International Journal of Rock Mechanics and Mining Science, Vol. 36 (1999), p. 839-842

Experimental Section Materials and Instruments.
Fig. 5 The tensile stress-strain curves of electrospun PAN fibrous materials.
Dzenis, Material science: spinning continuous fibers for nanotechnology, Science. 304 (2004) 1917-1919
Baumgarten, Electrostatic spinning of acrylic microfibers, Journal of Colloid and Interface Science. 36 (1971) 71-79
Wang, Interior structure of polyacrylonitrile (PAN) nanofibers with LiCl, Materials Letters. 62 (2008) 1325-1327

Materials and methods Sample preparation.
Anang: Animal Feed Science And Technology, Vol. 81(3-4) (1999), P. 299
Z Ren et al: World Journal of Microbiology and Biotechnology, Vol. 23(10) (2007), P. 1393
Appu Rao: Journal of industrial microbiology biotechnology, Vol. 37(2) (2010), P. 129
Bello: Meat Science, Vol. 52(4) (1999), P. 403.

Applied Materials Today. 2024;37
Journal of Materials Research and Technology. 2023;27:3900-13
Advanced and Emerging Polybenzoxazine Science and Technology2017. p. 699-723
Body armour – New materials, new systems.
Mechanics of Advanced Materials and Structures. 2022;30(18):3699-709.

Interrupt electricity price from low to high is as follows: building materials, electronics, textiles, food, medicine, and mechanical.
The data from Table 1 shows, when the interruptible load is 80,000 kW, the interruption capacity of the building materials industry has reached the previously set maximum outage capacity limit, therefore impact the distribution of the outage capacity , That means, due to the maximum outage capacity constraints, other industries need share interrupt load that the building materials industry exceed the maximum capacity, so that the total cost of the building materials industry interrupt cost decline in the proportion.
JiLin Power Journal,2007,2
Zhejiang Electric Power Journal,2006(4) [5] He Yangzhan , Wen Zenyin.
Huazhong university of science and technology in press.2002,2

At present, great hopes in the field of cardinal improvement of the technology and quality of construction materials are connected with the use of nano- technologies and nano-particles.
Depending on the type of these bonds, the following contact types are marked out in condensed or crystal structures of disperse materials: direct atom contacts in dry powders and relatively weak forces of molecular interaction.
Such systems include the most part of raw compositions used for the production of construction materials The prevalence of capillary forces over others is especially appreciably for particles with the size more than 10 µm and up to 1…2 mm.
It opens potentialities of control over technological properties of raw compositions in the process of production of concrete, silicate, ceramics and other construction materials.
First the mechanism of capillary cohesion was proved for the silica sand, then it was proved for more complicated systems: the raw mixes used for the production of construction materials.