Search results

Magdy et al. [2] found that yield stress increased slightly with increasing the TPS content up to 20 wt%, and it began to decrease when TPS content up to 25 wt%.
Wang et al. [6] prepared TPS/LDPE blends using maleic anhydride as compatibilizer by one-step molding method, starch and polyethylene mass ratio was up to 7:1, but it was found that the one-step molding step may cause bad mixing of starch and glycerol, which affected the formation of thermoplastic starch.
Bikiaris et al. [7] used two-step molding to prepare LDPE/TPS plastic, thermoplastic starch was first prepared, and then adding a certain amount of the compatibilizer maleic anhydride grafted polyethylene (PE-g-MA) and LDPE to blend extrude LDPE/TPS plastic.
El-Naggar Abdel: Polymer Composites Vol. 29(2008), p. 1140

For the synthesis of Li (0.2, 0.4, 0.6, 0.8, 1.0, 2.0, 4.0, 6.0, 8.0 and 10 at. wt.%) and Al (0.5 at. wt.%) co-doped ZnO powders, aluminum nitrate (Al(NO3)3.9H2O) was employed as the source of Al.
Abu El-Fadl, E.M.
El-Maghraby, G.A.
Mohamed, M. bd El-Moiz, Rashad, Physica B: Condensed Matter, 370 (1-4) (2005) 158-167
Al-Sayyed, S.

Synchrosqueezing wavelet transform (SWT) proposed by Daubechies et al. [9] is a powerful TFA method which can efficiently improve the readability of TFR of signals with time-varying frequency.
El Badaoui, Cyclostationarity approach for monitoring chatter and tool wear in high speed milling, Mechanical Systems and Signal Processing, 44 (2014) 177-198
El Badaoui, F.

[3] Mohamed Kadjoudj, Mohamed El Hachemi Benbouzid, Chawki Ghennai, and Demba Diallo, “A robust hybrid current control for Permanent-Magnet Synchronous Motor” IEEE Transactions On Industrial Energy Conversion. vol. 19, no. 1, pp.109-115, March 2004
Nasir Uddin et al.
El-Saadany, “A Current Control Scheme With an Adaptive Internal Model for Torque Ripple Minimization and Robust Current Regulation in PMSM Drive Systems, ” Transactions on Energy Conversions vol. 23, no. 1, pp. 92-100, March 2008

Oyen et al. [9] presented viscous-elastic-plastic models for the time-dependent indentation behavior for several polymers including polyurethanes.
,)ln 2 1 ( 2 )3( 5 1 0 122∑= − − − +− = i el el ii i l i J JK I C GU λ (1) where G is related to the instantaneous shear modulus G0 as 8 6 4 2 0 67375 42039 875 513 175 99 53 1( l l l l GG λ λλλ ++++= ), (2) 1I is the first strain invariant defined as 3211 λλλ ++=I (3) Ci are constants and Jel is the elastic volumetric strain.

Very recently, Barlas et al [12] studied the SPP characteristics of III-V porous semiconductors (InP, GaP and GaAs).
Mauriz, F.F. de Medeiros, E.L.
El-Gohary, K.A.

Prete et al. attempted to study on turning operation optimization on Inconel 718 [11].
El Baradie and M.
El-Baradie, Machinability Assessment of Inconel 718 by Factorial Design of Experiment Coupled with Response Surface Methodology, Journal of Materials Processing Technology Vol. 95,(1999), pp. 30-39 [10] E.

The same failure for reinforcement ratios greater than the balanced reinforcement was also reported by El-nemr and Adam [9-10].
Wang, et al, Effects of Stirrup and Inclined Bar Corrosion on Shear Behavior of RC Beams, Construction & Building Materials 98 (2015) 537–46
El-nemr, E.

El-Naggar, M.M.G.
Al-Deyab, M.H.
El-Rafie, Highly effective antibacterial textiles containing green synthesized silver nanoparticles, Carbohydrate Polymers. 86 (2011) 936-940

This raw material was prepared by weighing the powder of B2O3, TeO2, Li2CO3 and Nd2O3 using electronic balance model Setra EL-2008.
[14] El-Deen, L.
S., Al Salhi, M.