Search results

In three kinds of materials, the hardness of A31 is highest (68HRC).
Zhai: Materials Science & Technology, Vol. 16(2) (2008), p.271 [2] L.
Long: Chinese Journal of Mechanical Engneering, Vol. 44(9)( 2008), p.50 [5] Z.
Mei: Journal of Engineering Thermophysics, Vol. 17(1)( 1996), p.346 [8] X.
Ai: Engneering Science, Vol. 2(11)( 2000) , p.40 [9] Z.

In the field of polymer materials crack behaviour at the bi-material interface is described in paper [9].
Kaddouri et al.: Computational Material Science, Vol. 35 (2006), p. 53
Sadowski : Computational Material Science, Vol. 44 (2009), p. 941
Hutař: Key Engineering Materials, Vol. 417-418 (2010), p. 301
Hutař: Computational Materials Science, Vol. 46 (2009), p. 614

The impact strength of materials were tested by impact tester (provided by WUZHONG Company ,JB－5).
When the mass fraction of PUP is 15%, the results of the materials are best.
Journal of Central South University: Natural and Science,2007, 38(2):213-217(in Chinese)
European Polymer Journal,2005,41(10):2370-2379
Journal of Applied Polymer Science, 2006, 100(1): 323～328

This study aims to give valuable insights to the construction industry regarding sustainable practices by utilizing waste materials in concrete production.
Introduction The construction industry is continually seeking innovative solutions to enhance the sustainability of building materials and reduce environmental impact.
Materials and Methods Table 1.
Materials used details Water Portable water Cement Ultratech OPC (53 Grade) Fine Aggregate Zone-2 Coarse Aggregate 20mm Passing and 12.5mm Retained Ceramic Waste Obtained from nearby tile shops Ceramic waste, fine aggregate, coarse aggregate, and cement are the materials employed in the study.
Rakesh Kumar Singla, Utilization of waste ceramic tiles as coarse aggregate in concrete, Journal of Multidisciplinary Engineering Science and Technology, Vol. 2 Issue 11, November – 2015

For solid materials (condensed state materials) there are two basic types of structural order: crystalline materials (which has a long-range ordered structure) and systems which have not reached steady state with short-range order (such as amorphous solids, vitreous).
For X-ray study of materials is indicated only a small range of wavelengths.
Also, be aware of an ordered amorphous phase, which will give good resistance material in oral cavity, much better than other ceramic materials (ie HERA CERAM material ).
D.SING diffractogram It can be observed for D.SING material diffractogram one hardness shoulder slightly lower compared to other ceramic materials.
Kunzmann, High-temperature X-ray diffraction analysis of a low-fusing dental ceramic, JournaL of Materials Science, (2001), p. 5403-5406

Ni-based alloy welding material has been widely used in the welding and post-welding repair of high-temperature materials.
Ye, D.K.L.Tsang, et al.Welding solidification cracking susceptibility and behavior of a Ni-28W-6Cr alloy, Journal of Materials Science & Technology, 35 (2019) 29-35
Microstructure characteristics and temperature-dependent high cycle fatigue behavior of advanced 9%Cr/CrMoV dissimilarly welded joint, Materials Science and Engineering A, 615 (2014) 98-106
Zhang, Fatigue crack growth behavior of a new type of 10%Cr martensitic steel welded joints with Ni-based weld metal, Journal of Materials Engineering and Performance, (2017) 1-8
International Journal of Fatigue, 88 (2016) 78-87.

Accelerated creep testing for aramid fibres using the stepped isothermal method (2008) Journal of Materials Science, 43(14), pp. 4789-4800
Accelerated and real-time creep and creep-rupture results for aramid fibers (2012) Journal of Applied Polymer Science, 125(5), pp. 3856-3870
Prediction of the long-term behaviour of high modulus fibres using the stepped isostress method (SSM) (2011) Journal of Materials Science, 46(24), pp. 7660-7671
Comparison of accelerated compressive creep behavior of virgin HDPE using thermal and energy approaches (2011) Journal of Materials Engineering and Performance, 20(7), pp. 1219-1229
Predicting compressive creep behavior of virgin HDPE using thermal acceleration (2011) Journal of Materials in Civil Engineering, 23(8), pp. 1154-1162

Hot Zone Materials.
Two commercially available materials were evaluated.
Madar: Materials Science and Engineering B46 (1997) p. 278
Madar: Materials Science and Engineering B61-62 (1999) p. 58
Philipps: Journal of Nuclear Materials 220-222 (1995) p. 756

Chernyaev, Crack resistance and mechanical properties of structural materials of technical systems, Science, Novosibirsk, 2002
Khlusova, Structure and the properties of cold-resistant steels for the constructions of Northern design, Scientific and technical journal "Voprosy Materialovedeniya", Materials Science Issues. 1(45) (2006) 24-44
Scientific and technical journal "Voprosy Materialovedeniya", Materials Science Issues. 4 (96) (2018) 14-41
Igolkin, Strength of structural elements with cracks, IOP Conference Series: Materials Science and Engineering. 1 (826) (2020) 012015
Solovev, Energy Parameters of the Binder during Activation in the Vortex Layer Apparatus, Materials Science Forum, Vol. 945 (2019) 98-103.

Kumar, Machining of WC-Co composites- A review, Material Science Forum 808 (2015) 51–64
Husain, Machining of cemented tungsten carbide using EDM, Journal of Applied Sciences 11(10) (2011) 1784–1790
Khamba, Investigation for ultrasonic machining of titanium and its alloys, Journal of Materials Processing Technology 183 (2007) 363–367
Mohapatra, An investigation into the machining characteristics of titanium using ultrasonic machining, International Journal of Machining and Machinabaility of Materials 3(1/2) (2008) 143–161
Kumar, Ultrasonic machining - A compressive review, Machining Science and Technology: An International Journal 17 (3) (2013) 325–379