Search results

By creating a moving local hot spot around the contact point between tool and sheet, process forces can be reduced while forming limits are increased for most materials.
Secondly a brief overview is given on the material of choice for this study.
Material: The material of choice is AA 5182-O, containing 4.5 wt% Mg and 0.35wt% Mn.
This could be due to the buildup of material on the tool.
Also special recognition goes to the Flemish agency for innovation by science and technology IWT for its support through ISF Light.

Generally, in steel turning, increasing in material removal rate, decreases surface finishing and vise versa.
Therefore, when the weight of material removal rate is 1 and the weight of surface roughness is 0 then, the material removal rate will be maximum and visa versa.
Loganathan: A new heuristic optimization algoritm;harmony search, Journal of Simulation,76/2 (2001), p 60-68
Teller: Equations of state calculations by fast computing machines, Journal of Chemistry Physics Vol. 21 (1953), p. 1087- 1092
[7] F.Glover: Heuristic for integer programming using surrogate constrains, Journal of Decision Science Vol. 8/1 (1977), p. 156-166.

K-values, derived from numerical simulation, for different materials were virtually equivalent for the 12 mm bend radius.
The differences between different materials found in the experimental study could not be detected.
In comparison, bend angle and materials investigated here only have little effect on the initial sheet width.
J. de Vin, Expecting the unexpected, a must for accurate brakeforming, Journal of Materials Processing Technology. 117 (2001) 244-248
Altan, Prediction of bend allowance and springback in air bending, Journal of manufacturing science and engineering. 129 (2007) 342-351

The phosphobetaine amphoteric surfactant of N, N-dimethyl-tridecane hydroxyethyl ammonium phosphate (PBET-13), was synthesized by using epichlorohydrin, NaH2PO4 and dodecyl/tetradecyl dimethyl amine and cetyl/octadecyl dimethyl ammonium as raw materials.
In this paper, we synthesized the new surfactant of dodecyl/tetradecyl phosphobetain (PBET-13) based on the dodecyl/tetradecyl dimethyl amine as the main raw material, and its scale inhibition performance, interfacial tension and foaming performance were studied.
Journal of Surfactants and Detergents.14(3):433-438
Journal of colloid and interface science. 2004,276(1):197-207

School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China 2.
Materials and Experimental The aluminum-silicon alloys used in this work were Al-12Si(wt.%) and Al-20Si(wt.%).
This was typical for those materials, and similar results were obtained in Al-Si eutectic alloys[8] and AlSi12CuMgNi matrix composite [9] .
Chung: Journal of Material Science Vol. 24 (1994), p. 6181-6198 [6] L.
Berry: Journal of Applied Physics Vol. 24 (1953), p. 658 [11] Y.

Materials and methods Preparation of silk fibroin solution.
This may demonstrate that the SF/PYR blend films will be a good choice for biomedical materials.
Cebe and D.L.Kaplan, Water-Stable Silk Films with Reduced β-Sheet Content, Advanced Functional Materials. 15 (2005)1241-1247
Kaplan, Water-stable silk films with reduced beta-sheet content, Advanced Functional Materials.15 (2005)1241-1247
Tsukada, Biodegradation of Bombyx mori silk fibroin fibers and films, Journal of Applied Polymer Science. 91(2004)2383-2390.

Introduction Organic polymer semiconductors are becoming a great alternative to inorganic semiconductors due to complexity fabrication process and high cost of silicon materials [1-4].
The PCDTBT parameters were defined before analysis in the material and mobility field.
The PCDTBT was not included in the library materials of the software therefore it was specified as user defined material.
[3] Dennler, G., et al, Polymer‐Fullerene Bulk‐Heterojunction Solar Cells, Advanced Materials, Vol. 21,1323-1338, 2009
[4] Espinosa, N., et al, Solar cells with one-day energy payback for the factories of the future, Energy & Environmental Science, Vol.5, 5117-5132, 2012

Current Opinion in Solid State & Materials Science, 3(1998), p.309
Advanced materials, 12 (2000), p894
Ding, Materials Science and Engineering, R. 47(2004), p49
Journal of Biomedical Materials Research, 51(3) (2000), p. 398
Materials Letters , 2003(57): 2 066

It is obvious from presented in this paper that team must be comprised by experts for machine design, numerical analysis, materials, welding, corrosion and machining.
Heinloth (ed), Landolt-Börnstein, Group VIII: Advanced Materials and Technologies, Vol. 3: Energy Technologies, Subvol.
Atanasovska, Assessment of the Effect of Pitting Corrosion on Fatigue Crack Initiation in Hydro Turbine Shaft, Advanced Materials Research, In A.
Subić,: Advances in Engineering Materials, Product and Systems Design (Special topic volume with invited peer reviewed papers only), Trans Tech Publications, Switzerland, (2013) p. 186-196
Vuherer, Methodology of determination the influence of corrosion pit on decrease of hydro trubine shaft fatigue life, Journal Machine Design, Published by University of Novi Sad, Faculty of Technical Sciences, Vol. 4 No.4, (2012) p. 231-236

Introduction Laminates are multilayer materials stacked by materials with various physical and chemical characteristics.
The bionic structures of laminates not only have component materials' virtue, but also possibly bring special property that different from component materials [1,2].
The stack order of raw materials is shown in Fig. 1.
Clyne: Materials Science and Engineering.
[6] S.Das, A.N.Tiwari, A.R.Kulkarni: Journal of Materials Science.