Search results

Landers: Journal of Manufacturing Science and Engineering, Vol. 126 (2004), pp.297-310
Huang: International Journal of Production Research, Vol. 33 (1995), pp.705-728
Pande: International Journal of Production Research, Vol. 38 (2000), pp.3181-3202
Li: International Journal of Advanced Manufacturing Technology, Vol. 17 (2001), pp.665-669
Sahasrabudhe: Journal of Materials Processing Technology, Vol. 132 (2003), pp.203-214.

Journal of Sound and Vibration, 1991, 145: 321~332
Journal of Structural Engineering, 1992, 118(8): 2186-2203
Journal of Structural Engineering, 1999, 125(4): 410-416
Journal of Vibration and Shock, 2007, 26(6):116-120.
Journal of Sound and Vibration, 1994, 169: 3~17.

Bioleaching is technology applicable to iron extraction from low-grade non-metallic raw materials.
The feasibility of the bioleaching treatment has to be tested specifically to each type of silicate raw materials.
may have influence Fe chemistry in these non-metalic raw materials.
The feasibility of the bioleaching treatment has to be tested specifically to each type of silicate raw materials.
Geomicrobiology Journal 21, 2004, 135 - 144.

Materials & Processing Report. 9 (2010) 114-119
Journal of Composite Materials. (2017) 002199831772421
Review of low-velocity impact properties of composite materials.
Science & Engineering of Composite Materials, 2017, 25(3)
Journal of Composite Materials, 2003, 37(16):1415-1438

Materials and methods Materials.
Acknowledgements The authors would like to acknowledge the support of AdMaS – Advanced Materials, Structures and Technologies centre (Reg.
CZ.1.05/2.1.00/03.0097), Research programme: Development of advanced building materials; internal project Specific research FAST-J-12-4 and the research plan SUPMAT – Promotion of Further Education of Research Workers from Advance Building Material Centres CZ.1.07/2.3.00/20.0111 References [1] T.
World applied sciences journal. 13 (2011) 1 [4] A.
European Journal of Wood and Wood Products. 72 (2014) 1, s. 73-79.

Performance properties of polymer modified cement grouts for repair and rehabilitation of concrete pavement Shui Zhang1, Guozhong Li1,a, Chao Ning1, Haiyan Yuan2, b 1School of Materials Science and Engineering, University of Jinan, Jinan 250022, China 2School of civil engineering and architecture, University of Jinan, Jinan 250022, China amse_ligz@ujn.edu.cn (Corresponding auther.
Materials and methods Materials and mix proportion.
When repaired areas fail it is in many cases due to failure or partial failure of the bond between the old and new materials.
[3] Shiyun Zhong, Yingdiao Liu, and Peiming Wang: Journal of Building Materials.
(In Chinese) [4] Jianmao Yang, Xulong Cao, Shenling Zhang, Xingwang Song, Feng Qiu, and Yuanze Xu: Chemical Journal of Chinese Universities.

Modifying Effect of Al-Ti-C-P Master Alloy on Hypereutectic Al-Si Alloy Chunxiang Xu a, Liping Liang b, Binfeng Lu c, YongjunXue d, Jinshan Zhang e, Liang Wei f School of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024, Shanxi.
Recently, Al-Cu-P wire-rod has been fabricated via a power metallurgy technique using aluminum powder (99.99% pure) and Cu-P master alloy as raw materials [11].
Zhong: Materials Science & Technology, 2001, vol. 9(2), p. 117-21 [3] C.X.
Bian: Rare Metal Materials and Engineering, 2004, vol. 33(9), p. 924-27 [5] J.G.
Bian: Materials Science & Technology, 2001, vol. 9(2), p. 211-14 [10] J.G.

Introduction Er doped fiber amplifiers (EDFAs) have used silica or silicate glasses based fibers as host materials because the characteristics of the materials for optical fibers are similar to those of the silicate glasses.
However, the full width at half maximum (FWHM) of these materials is about 45 nm with a non-flat gain at 1550 nm.
Peyghambarian, Journal of Non-Crystalline Solids Vol. 255 (1999), p. 97 [5] A.
Soga, Journal of Applied Physics Vol. 85 (1999), p. 2046 [6] S.
Kar, Journal of the American Ceramic Society Vol. 85 (2002), p. 1391 [7] S.

Engineering Materials, Processes.
In: Journal of Materials Science & Technology, 28 (2012) 1, 1-14
In: Journal of Materials Science, 28 (1993) 18, 4892-4899
[8] DIN EN ISO 6892-1:2009-12: Metallic materials - Tensile testing - Part 1: Method of test at room temperature.
[9] DIN 50125:2009-07: Testing of metallic materials - Tensile test pieces.

Acknowledgements All the research works are supported by the National Natural Science Foundation of China under granted No.50705044, the Natural Science Foundation of Zhejiang Province of China under granted No.Y1080094, and the Natural Science Foundation of Ningbo City of China under granted No. 2010A610132 and 2010A610133.
Journal of Intelligent and Robotic Systems(2000)29,p.295–308 [3] J.D.
Key Engineering Materials (2009) 392-394, p.771-776 [7] J.M.
Key Engineering Materials (2011) 455, p.181-185 [8] Qitong Liu, Jianming Zhan and Jianhua Mao.
Applied Mechanics and Materials (2010)37-38, p.1327-1331