Search results

The 'embed'[10] technology is used to embed rebar and steel into concrete that relative sliding between two materials does not occur.
Because concrete is the material of poor tensile properties and prone to brittle failure.
Journal of Building Structures. 2008,29(3).128-135
Jo urnal o f Shenyang Jianzhu University ( Natural Science). 2009,25(4).656-662
Journal of Constructional Steel Research, 2000,53: 87-111 [7] Samuel Tan.

Mechanical pulping is a kind of high yield pulping that comes with the comprehensive utilization of plant material.
Introduction We are facing raw material and energy shortage, environment pollution problems in our paper-making industry.
Experimental Materials.
[3] Pllinen J, A buhasan J, Journal of Biotechnology, 1989, 10(2): 161
M., Average fiber length and its instrumental measurement result analysis, Paper Science& Technology, 3: 35-37 (2003)

Research on Polyvinylidene Fluoride Hollow Fiber Hemodialyzers Guo Jianhui, Zhang Juan, Lv Xiaolong State Key Laboratory of Hollow Fiber Membrane Materials and Processes (Tianjin Polytechnic University) Tianjin, China Corresponding author.
Abstract.Hemodialysis is the main treatment of acute and chronic renal failure, and the selection of hemodialysis membrane materials is the key factor that determines the curative possibilities.
Up till now, the membrane materials adopted by high-flux hemodialysis are mainly polysulfone (PSF) and polyether sulfone (PES).
The New England Journal of Medicine, 2002, 347(25): 2010-2019
Journal of Biomedical Engineering, 2010, 27(1): 91-96.

Mickiewicza Av. 30, 30-059 Krakow, Poland 2AGH University of Science and Technology,  Academic Centre for Materials and Nanotechnology, A.
The microstructure of these materials in the state as delivered is shown in Figure 1.
Mittemeije, Recovery, recrystallization and grain growth, Fundamentals of Materials Science, The Microstructure, Property, Relationship Using Metals as Model Systems, Springer-Verlag Berlin Heidelberg, 2010, pp 463-496
Hutchinson, On the effect of pre-recovery on subsequent recrystallization, International Journal of Materials Research 100, 10 (2009) 1446-1448
Rdzawski, Misorientation in rolled CuTi4 alloy, Archives of Materials Science and Engineering 52, 1 (2011) 5-12

Material and methods Sample preparation and pre-treatments.
Journal of the Environmental Engineering Division. 103(1977) 815-828
Journal of Fudan University (Natural Science). 50(2011) 556-562.
Journal of Hazardous Materials. 154(2008) 1120-1126
Journal of Systems Science and Systems Engineering. 13 (2004)1-35

McKeown: Computational Materials Science Vol.21(2001), p. 375-394
Xiong: Journal of Materials Processing Technology Vol.121 (2002), p. 1-4
Sha: Computational Materials Science Vol.32 (2005), p.1-12
[5] Li M., Liu X., Wu S. and Zhang X.: Materials Science & Technology Vol. 14 (1998), p. 136-138
Yu: Materials Science and Engineering A, Vol. 393(2005), p.204-212.

Introduction Recently, several studies on Incremental Sheet Forming were presented in literature and most of them are focused on materials formability [1-4] and on the development of models able to predict material response, before any experimental test [5-6].
This results shows a high potential thinking to the possibility to investigate the application of SPIF to new materials or including new variables, such as the temperature during material processing at non-room temperature. 2.
Yang Improvement of formability for the incremental sheet metal forming process, International Journal of Mechanical Sciences Vol.42 (2000), 1271-1286
Tekkaya The increased forming limits of incremental forming processes, Key Engineering Materials Vol. 344 (2007), 621-628
Meyer, Finding the Active Factors in Fractionated Screening Experiments, Journal of Quality Technology, Vol. 25 (1993), 2, 94-105

Stiffness computation and identification of parallel kinematic machine tools.Trans ASME, Journal of Manufacturing Science and Engineering, 2009, 131: 1-7
Chinese Journal of Mechanical Engineering,2007,43(9) :151-155
Journal of Beijing University of Technology,2007, 33(12) :1246-1251
European Journal of Mechanics A/Solids, 2009,28: 461-468
Mechanical Science and Technology,1996,15(6) :863-870

being the pitching scanning angle and Journal Title and Volume Number (to be inserted by the publisher) 177 ¹the azimuth scanning angle.
Assuming the electrical inductivity of the radome material is uniform and the geometric thickness of the radome wall satisfies the design requirement, the boresight error of such a radome will be within the tolerance.
Acknowledgement The financial support for this research by the National High Technology Research and Development Program of China under grant No. 2001AA421170 and the National Natural Science Foundation of China under grant No. 59935110 is greatly appreciated.
Jia: Chinese Journal of Mechanical Engineering Vol. 37 (2001), p. 92 (in Chinese) [4] F.Z.
He: Journal of Capital Normal University (Natural Science Edition) Vol. 17 (1996), p. 23 (in Chinese)

Examples and Computational Analysis Physical Properties of Materials.
At different temperatures the physical parameters of these materials remain basically unchanged.
According to the table, the related parameters about three materials, seal medium and circulating water were listed in Table 1, 2.
Journal of Ship Mechanics Vol.12-3(2008).p.483-489.
Journal of TriblogyVol. 123(2001), p.388-394