Search results

Huan Luo et al [12] investigated Structural properties of calcium chalcogenides compression up to 52 GPa using energy-dispersive x-ray-diffraction techniques.
Jha et al [26] and Mahendra Aynyas et al [4] investigated phase transition and related properties of calcium chalcogenides at high pressure respectively using three body potential model and two body inter ionic potential approach with modified ionic charge (Zm).
Slimani et al[3] studied the structural, electronic, optical and thermodynamic properties of CaS1−xTex, CaSe1−xTex and CaS1−xSex using ab initio method.
El Haj Hassan “Ab initio investigations of calcium chalcogenide alloys” Journal of Alloys and Compounds 485 642–647, (2009) [4] B.S.
Li, A.L.

Primary alloy design result and mechanical properties by rebar diameter Diameter [mm] Billet size [mm] C Mn V N YS [MPa] TS/YS EL [%] SPEC. - - - - 550~675 1.25↑ 10↑ D13 120 0.28 1.38 0.090 0.010 595 1.29 18.2 D19 575 1.32 14.8 D22 200 0.110 593 1.24 15.8 D43 554 1.30 18.6 First, as shown in Table 1, all of the required materials were satisfied.
Recently, Milbourn et al. [7], also reported that the increase in KVN is disadvantageous to TS / YS ratio.
References [1] Hany Khalifa et al., “Experimental investigation and simulation of structure and tensile properties of Tempcore treated rebar”, J.
Kim et al., “Effect of microstructure on the yield ratio and low temperature toughness of linepipe steels”, ISIJ Int., 42(2002), pp.1571-1577
[6] Fuaso Ishikawa et al., “Intragranular ferrite nucleation in medium-carbon vanadium steels”, Metal.

[2] Dan ZHANG, Hui LIU, Ying LIANG, at el.
[3] Dargnat C, Teil M J, Chevreuil M, et al.
[5] Liang Renxing, WU Xueling, Wang Xingna, et al.
[10] Bin Xu, Nai-yun Gao, Hefa Cheng, et al.
[12] Shen Yanyan, Xu Qian, Yin Xueyan, et al.

Anderson et al. [9] focused on tool wear, where they reported lower LAM flank wear compared to CM.
In a study by Dumitrescu et al. [3], high power diode laser was used in turning hardened AISI D2 tool steel.
As an example, Bouchnak et al. [10] modelled LAM of 42CrMo4, where cutting forces dropped at different cutting speeds.
In another study, Shi et al. [11] developed a FE model that included a new constitutive material model, friction model and heat transfer model.
[19] T.I El-Wardany, H.A.

The electrodeposited Ni films were widely used to improve mechanical and corrosion properties of Al, Mg, Cu and other alloys.
Experimental Experimental samples were two-layer thin-film compositions of Al and Ti, deposited on Si/SiO2 (d=76 mm) substrates.
Trukhanov, E.L.
Zdorovets, A.L.
%Al composite coating in 3.5%NaCl solution, Port.

The peak at lower temperature region (350 – 450 °C) reflects the first stage of reduction for reaction in Eq. 3 and in agreement with Sharma et al. [11] and C.
Feng Cheng et al. [12] whose reported that the reduction of NiO to Ni was started at temperature above 500 °C and completed as T = 700 °C.
Both peaks were representing the reduction of Co3O4 (Eq. 4) and CoO (Eq. 5) as discussed by Shouli et. al. [13].
The reducibility NiO become lesser after loading with Co was also in agreement with Zhu et al. [16] as Co doping lowered the reducibility of lattice oxygen of Ni species.
El.

Lamprou, et al., 3D printed microneedle patches using stereolithography (SLA) for intradermal insulin delivery, Mater Sci Eng C. 102 (2019) 743-55
Wen, et al., Preparation and investigation of novel gastro-floating tablets with 3D extrusion-based printing, Int J Pharm. 535 (2018) 325-32
Buanz, et al., Fabrication of controlled-release budesonide tablets via desktop (FDM) 3D printing, Int J Pharm. 496 (2015) 414-20
Jin, et al., Combination of 3D printing technologies and compressed tablets for preparation of riboflavin floating tablet-in-device (TiD) systems, Int J Pharm. 549 (2018) 370-9
El-Say, Optimized gastroretentive floating carvedilol tablets: an approach for prolonged gastric residence time and enhanced absorption, J App Pharm Sci

Nasser et al. [2] investigated the behavior of beams with a single large web opening, it was concluded, diagonal steel reinforcement more effective method to resist shear stresses at the corner of the opening.
M.A Mansur et al. [3] compared previous studies in literature and the results founded from theoretical predictions for a reinforced concrete beam with large openings, it was concluded, load collapse depends on size and positions of openings.
M.A Mansur et al
Amiri et al. [7], studied nine beams with circular openings for flexure, shear, and ultimate load, and the parameters of the study were size and positions of openings, and type and locations of steel reinforcement around the opening in additional to the concrete strength.
El-Kashif, Computational model of ultimate capacity and behavior of reinforced concrete beams with multiple openings, Al-Azhar University Civil Engineering Research Magazine, 2018 249-267

Tamanna Afrin Tisa et al, worked on an enhanced temperature control system for incubator infants which in their research had combined a combination of Pulse Width Modulation (PWM) and a simple ON-OFF control system [11].
Wayan Widhiada et al, built a baby incubator with On / Off Control used to help the temperature distribution in the incubator.
El Majzoub, and A.
El Majzoub, and A.

The synthesis method were applied due to the synthesis methods as mentioned by Noruzi et al. [34], Luo et al. [35], and Byranvad and Kharat [36] with minor changes.
El-Ads, A.
El-Ads, Gold nanoparticles-coated poly(3,4-ethylene-dioxythiophene) for the selective determination of sub-nano concentrations of dopamine in presence of sodium dodecyl sulfate, Electrochim.