Search results

Prakash 2, c 1 Baba Banda Singh Bahadur Engineering College, Fatehgarh Sahib, Punjab, India 2 Indian Institute of Technology, Roorkee, Uttrakhand, India a nirajbala1@rediffmail.com, bhn1998@gmail.com, ctruthfmt@iitr.ernet.in Keywords: Cold spray, Critical Velocity, Coatings, Thermal Spray.
Conclusion Cold spray coatings is a unique technology that allows to fabricate dense, low oxide-content deposits of ductile materials like aluminium, stainless steel, copper, titanium and alloys, but it is limited to ductile materials only, hard and brittle materials like ceramics can not be sprayed in the pure form, but may be applied as composites with a ductile matrix phase.
Being a relatively young process considerable R&D efforts are needed to understand and control the process, as well as develop engineered coatings with desired properties for specific applications.
Lindemann, Journal of Materials Science Letters, Vol. 21 (2002), p. 1687-1689 [2] Information on http://www.thermalspray.org [3] F.
Karthikeyan, Cold Spray Technology: International Status and USA Efforts, 2004, p. 1-14 [10] D.E.

Sofyan1,b 1 Dept. of Metallurgy and Materials Engineering, Faculty of Engineering, Universitas Indonesia, Depok 16424, Indonesia asigmardi@gmail.com, bbondan@eng.ui.ac.id Keywords: aluminium composite, lightweight, ballistic, precipitation hardening, magnesium, wetting agent interface.
Ceramic SiC particles as reinforcement will contribute on composite hardness.
Materials Science and Engineering A, 2010. 527(7): p. 2036-2044
International Journal of Impact Engineering, 2011. 38: p. 745-754
Materials Science and Engineering A, 2004. 382(1): p. 351-361

Experiment was provided in the laboratory of Faculty of mechanical engineering VUT Brno, Czech Republic.
To, Analytical modeling and prediction of cutting forces in orthogonal turning: a review, The International Journal of Advanced Manufacturing Technology 119 (2022) 1407–1434
Wagner, Machinability of High Mn Steel Using Tool Life Criteria, International Journal of Metalcasting 18 (2023) 600-607
Ekici, An Experimental and Statistical Evaluation of The Cutting Parameters on The Machinability of Hadfield Steel, Materials Science, Engineering, (2016)
Series: Materials Science and Engineering, 161 (2016)

IOP Conference Series: Materials Science and Engineering Vol. 441.
IOP Conference Series: Materials Science and Engineering.
Materials Science and Engineering: C 62 (2016): 852-859
Journal of Ceramic Processing Research. 2017 Vol.18, Issue 2, pp.103-107 [11] Vdovin, R.
IOP Conference Series: Materials Science and Engineering.

MEMS is not a single product or market, but an engineering tool-kit applied to a wide array of markets.
This leads to a more diverse technology base with more development and engineering work and therefore to a more expensive and more difficult to maintain technology.
Muhammad Waseem Ashraf, Shahzadi Tayyaba and Nitin Afzulpurkar, Micro Electro- mechanical Systems(MEMS)Based Microfluidic Devices for Biomedical Applications, International Journal of Molecular Sciences, 12, 2011, 3648-3704 [14].
Nelson, Passive Wireless MEMS Microphones for Biomedical Applications, Journal of Biomechanical Engineering, 127, 2005, 1030-1034 [15].
Micromechanics and Micro- engineering, 16, 2006, 2618-2631

International Journal of Polymer Analysis and Characterization, 23 (4) (2018) 383-395
International Dairy Journal, 16(11), (2006), 1241-1251
International Journal of Biological Macromolecules, 81, (2015), 608-614
International journal of biological macromolecules, 102 (2017) 1092-1103
Brazilian Journal of Chemical Engineering, 34(1) (2017) 253-261

The sulfur concentration was determined by SO2 measurement during oxidizing smelting of the samples in the ceramic crucible by infrared absorption method.
Xiao, Review on treatment and utilization of bauxite residues in China, International Journal of Mineral Processing 93 (2009) 220-231
Sahoo, et al., Progress of Red Mud Utilization: An Overview, American Chemical Science Journal 4 (2014) 255-279
Bychinskii, et.al., Extraction of Alumina from high-silica bauxite by hydrochloric acid leaching using preliminary roasting method, IOP Conference Series: Materials Science and Engineering 110 (2016) 012049
Torricelli, Reuse of treated red bauxite waste: studies on environmental compatibility, Journal of Hazardous Materials B117 (2005) 55-63

Citation & Key Engineering Materials Vols
Xu College of Mechanical Engineering and Automation, Huaqiao University, Quanzhou, Fujian Province 362011, P.R.
Segment Load distribution Sawing direction Key Engineering Materials Vols. 67 References [1] B.N.
Wang: Key Engineering Materials Vol. 202-203 (2001), p. 199 [5] D.N.
Shen: Ceramic Transactions Vol.102 (1999), p. 38 [8] Y.K.

The Study on the Ultrasound Assisted Atomic Force Microscopy Base Nanomachining Jen-Ching Huang 1,2,a, Yung-Jin Weng 3, Huail-Siang Liu4, Feng -Chin Tsai1, and Fu-Jen Cheng5 1 Department of Mechanical Engineering, Tungnan University, Taiwan 2 Research Center for Micro/Nanotechnology, Tungnan University, Taiwan 3 Department of Information Communications, Kainan University, Taiwan 4Institute of Mechanical Engineering, Tungnan University, Taiwan 5 Department of Electrical Engineering, Tungnan University, Taiwan 1,2a jc-huang@mail.tnu.edu.tw, 3 yjweng@mail.ncyu.edu.tw, 4 q3677293@yahoo.com.tw 1fctsai@mail.tnu.edu.tw, 5 fjcheng@mail.tnu.edu.tw Keywords: Ultrasonic assisted, Nanomachining, Atomic Force Microscopy, Quartz Crystal Microbalance.
Lee, Evaluation of the Nanofabrication and Corrosion on Copper by In-situ ECAFM, Journal of Chinese Society of Mechanical Engineers 32 (2011) 61-66
Tseng, The influence of the bias type, doping condition and pattern geometry on AFM tip-induced local oxidation, Journal of the Chinese Institute of Engineers 33 (201) 55-61
Huang, Study of precision micro-holes in borosilicate glass using micro EDM combined with micro ultrasonic vibration machining, International Journal of Machine Tools & Manufacture 42 (2002) 1105-1112
Sun, Material removal-rate analysis in the ultrasonic machining of enginerring ceramics, Journal of Materials Processing Technology 88 (1999) 180-184

Radovanovic, Laser cutting machines for 3-D thin sheet parts, 8th International Conference, Universitatea "Constantin Brâncusi" din Târgu-Jiu, Târgu-Jiu, 2002
Bredt, Laser machining of ceramics and metals.
Caristan, Laser cutting guide for manufacturing, Society of Manufacturing Engineers, 2003
Morar, R.E.Breaz, Researches regarding the assessment of manufacturing accuracy of numerically controlled machine-tools, Academical Journal of Manufacturing Engineering, vol 12, Issue 1/2014, ISSN 1583-7904, 2014, pp.14-19