Search results

Adriele et al [11] also showed that when the reaction time increased the magnetite phase decreased with an increase in the hematite phase and the Peak intensities are seen to increase due to the increase in crystallinity and particle size.
Al-Mamun, M.
D Souza, Kinetics of Thermal Transformation of Synthetic Al-Maghemites into Al-Hematites, Revi.
Al-Alawy, Synthesis and characterization of coated magnetic nanoparticles and its application as coagulant for removal of oil droplets from oilfield produced water, AIP Conf.
El Afifi , M.F.

Similarly, as reported by Ezuqwu et al. [5] increasing the cutting speed and feed rate increases the hardness and depth of the affected layer.
Ezugwu et al. [5] had shown that high pressure coolant supply demonstrated thinner deformation layer as in comparison to conventional coolant supply.
Zou et al. [4] reported that surface cavities were associated with the plastic deformation.
Sharman et al. [6] reported that surface cavities, tearing and smearing were the dominant surface damage when using new tools.
El-Khabeery, S.M.

Allam Musbah Al-Allam and Dr.
Proc., vol. 1846 (2017), p. 2008-1 [5] Masirin, M.I.M, Al Allam, A.M. and Ali, A.S.B: Pertanika Journal of Science and Technology, vol 25 (2017), p. 101 [6] H.
El-Badawy, A.
Al-Mansob, and D.
Al-Qadi, P.

Aqueel Ahmad et al proposed a solution to the misalignment issue using a Hall-effect sensor analyzed through finite element analysis.
Yuan-Hua Zhang et al proposed a wirelessly charging battery system that automatically adjusts its position to an optimal charging location using an XY-axis movable platform.
Villa et al suggest improvements and investigate the behavior of wireless power transfer systems that require precise coil alignment for optimal energy transfer.
The practical application of wireless charging was proposed by Aqueel Ahmad et al.
El-Shahat, A.

Dennis, E.L.
Latta, A.L.
Ip et. al.
Maas et al., Long-term evaluation of Bennett's fracture: A comparison between open and closed reduction, J Hand Surg, 19B (1994) 373-377
Vilcioiu, et al., Experimental evaluation on rat model of different bioresorbable materials potentially used as orthopedic biomaterials.

Pang, et al: European Polymer Journal (2019), in press
El-Sheikh: BioResources Vol. 9 (2014), pp. 8-23
Cai, et al: Industrial Crops and Products Vol. 65 (2015), pp. 27-35
Sun, et. al: Carbohydrate Polymers Vol. 37 (1998), pp. 351-359
Filho, et al: Carbohydrate Polymers Vol. 73 (2008), pp. 74-82

S., El-Kheshen, A.
A., et al.
[10] Koumpouri, D., Karatasios, I., Psycharis, V., et al.
[11] Kacimi, L., Simon-Masseron, A., Salem, S., et al.
R., et al.

The flow rate of argon gas and HMDSO in the liquid phase was controlled by a mass flow controller (MFC) and an EL-Flow (digital mass flow meter and controller), respectively, set at 20 standard cubic centimeters per minute (sccm) and 20 g/hr.
Takai, et al., JOCCA Surf.

Phumying et al. have successfully prepared magnetic oxide nanoparticles by a novel aloe vera extracted solution-hydrothermal method [6, 7].
Lu, E.L.

Samples were then loaded into a vacuum deposition chamber to deposit the 100 nm thick Al cathode.
Jeffries-EL, G.