Search results

The key components of advanced automotive and aerospace industries are gradually using lightweight and highly reliable materials to replace traditional components that consume energy due to weight.
The appearance is a block material of 20mmx20mm and a thickness of 10mm.
Acknowledgements The authors would like to express their appreciation to the Ministry of Science and Technology in Taiwan, R.
Govender, Predicting yield strengths of Al-Zn-Mg-Cu-(Zr) aluminium alloys based on alloy composition or hardness, Materials & Design, Vol. 99 (2016) p. 211-218 [3] I.J.
Li, Natural-ageing-enhanced precipitation near grain boundaries in high-strength aluminum alloy, Journal of Materials Science & Technology, Vol. 46 (2020) p. 107-113

Introduction Moisture environment has significant effects in physical and chemical properties of epoxy performance in joining the materials.
Like all polymeric materials, epoxy resin systems undergo physical ageing phenomena to reach the equilibrium condition [10].
Journal of Materials Science, 48(5)(2012)1873–1882
Construction and Building Materials, 30(2012)753–760
Materials & Design, 58(2014)125–129

In recent years, using natural minerals such as clay as the raw materials for the production of zeolites has become an promising trend compared to other synthetic routes.
Experimental Section Materials.
Applied Clay Science, 2004, 27(3)187-198 [3] Liu Xingyu, Xie Chuanxin, and Zhao Jing.
Journal of China University of Petroleum(Edition of Natural Science), 2004, 28(5)103-107 [4] Yin Xiaoyan, Zhao Qingyu.
Amsterdam; Elsevier Science Publishers B V, 1985

Introduction In this paper according to the material properties of structural steel and concrete under high temperature, the bonding strength changing laws with different temperature and its formula of the profiled steel sheet-concrete are deduced, and obtained the bonding stress-slip relationship, so as to established a nonlinear finite element method of analyzing the steel concrete composite slab fire properties.
Temperature distribution is unrelated to stress levels , whereby the temperature analysis will not consider the influence which component deformation, cracking, stress and strain level and other factors impact on the thermal parameters of materials and components thermal conduction. 4.
Material stress-strain line is a nonlinear elastic relationship.
Acknowledgements The Project was supported by Shandong Provincial Natural Science Foundation of China(Grant No.
J07YA09-1) References [1] Youlin Xu：Deformed bars—Experimental study of concrete on bond properties，PhD thesis , Tsinghua University，Beijing(1990) [2] Ye Sun：The Shear Behavior of a Composite Floor Slab with Modified Steel Sheeting Profile．Helsinki University of the Technology，Espoo.1998 [3] Hong Li,Weishan Jiang：Experimental study on steel and concrete bond constitutive relation, Journal of Northwestern Institute of Architectural Engineering，No．3，1995 [4] Inspection report：Bearing steel plate。

Effect of CuO Nanoparticles on the Cell Membrane Permeability of A549 and Its Exclusion Xiaoyan Xie a, Lili Xu b, Dongmei Gao c * Key Laboratory of Marine Environment & Ecology, Ministry of Education College of Environmental Science and Engineering, Ocean University of China Qingdao, China axxyxiexiaoyan@163.com, bxulili251143@126.com, cgaodongmei2002@yahoo.com.cn Keywords: CuO nanoparticles; A549; Cell membrane permeability; Exclusion Abstract.
Materials and Methods CuO NPs were purchased from Beijing Nachen S&T Ltd., China.
Materials Letters 58, 3324-3327
Journal of Nanoscience and Nanotechnology 10, 8638–8645

Introduction With the progress of science technology, change of consumption concept and improvement of living standards, more and more people hope that silk fabric trends towards the pluralism of high-level, unique, personality and novelty, thus its development and utilization are also increasingly attracted the attention of scientific and technological workers.
Materials and methods Materials.
Journal of Textile Rearch, vol.23(1985),p,63 [4]J.Y.

Experimental Procedure The material used in this study was directionally solidified by Bridgman method.
The material after casting was subjected to standard heat treatment(SHT), 1310℃2h/AC +1080℃4h/AC + 899℃16h/AC.
Fuchs, The effect of long-term thermal exposures on the microstructure and properties of CMSX-10 single crystal Ni-base superalloys, Materials Science and Engineering A. 381 (2004) 143–153 [5] Caron P, Y.ohta, Nakagawa Y G, Khan T, Creep deformation anisotropy in single crystal superalloys Superalloys 1988, S.Reichman et al., AIME, NY (1998) 215-224 [6] R.
Asgari, The effect of thermal exposure on the γ΄ characteristicsin a Ni-base superalloy, Journal of Alloys and Compounds. 368 (2004) 144–151

Effects of Deposition Temperature on the Growth Characteristics of CVD SiC Coatings Yanli Huo1,a and Yufeng Chen1,b 1 China Building Materials Academy, Chaoyang District, Beijing10024, China a xiaowen11920@yahoo.com.cn Keywords: CVD, SiC Coating, Deposition Temperature Abstract.
Kim: Journal of Materials Science Letters 10 (1991), p. 860

Starting material Resist coating Exposure Develop Etching Poly-si nanowires Fig. 1, Fabrication of poly- si nanowires using conventional photolithography.
[5] Robert Juhasz, Kai Kylmanen,Augustinas and Jan Linnros, Size-reduced silicon nanowires: Fabrication and electrical characterization, Elsevier, Material Science and Engineering ,pp 733-737, 2005
Fabrication of silicon nanowires by electron beam lithography and thermal oxidation size reduction method (2014) Advanced Materials Research, 832, pp. 415-418
Fabrication of High- Sensitivity Polycrystalline Silicon Nanowire Field Effect Transistor pH Sensor using conventional CMOS techmology.Japanese Journal of Applied Physics 50, Issue 4, (2011) pp.04DL05-04DL05-5

Precision Casting of GTD222 Component with Complex Thin-Wall Structure Guoliang ZHU1,a*, Wei WANG1,b, Rui WANG1,c, Guoxiang WANG1,d, Anping DONG1,e, Donghong WANG1,f, Zhiwu SHI2,g, Yulong LI2,h, Guodong ZHANG2,i 1Shanghai Key Lab of Advanced High-Temperature Materials and Precision Forming, Shanghai Jiao Tong University, Shanghai 200240, China 2Department of Materials Sciences and Manufacturing Processes, AECC Commercial Aircraft Engine Co., LTD, Shanghai 200241, China aglzhu@sjtu.edu.cn, bwei-1233@163.com, cwangrui1029@sjtu.edu.cn, dgxwang@sjtu.edu.cn, eapdong@sjtu.edu.cn, fwangdh2009@sjtu.edu.cn, gzwshi10s@alum.imr.ac.cn, hjadedragonlee@163.com, izgdhlx@sina.com Keywords: Precision casting; Numerical simulation; Gating system; Shrinkage Abstract.
Journal of Engineering for gas turbines and power 1993 (115):155-159