Search results

The mass fraction of MC carbides and M3B2 borides in the material was about 0.184%.
Maybe this is the main reason for improvement in rupture life of the material.
Yan et al., eds., China Aeronautical Materials Handbook, vol. 5 (Beijing: Standards Press of China, 2001), 44-47
Materials Science and Engineering A, 435/436 (2006), 83-99
Journal of Non-Crystalline Solids, 156/158(1993), 833-836

Typically, commercial Al2O3 materials which were crushed to 20-40 mesh were used as support, and calcined at 500 °C for 3 h, then vacuum filtration for 2 h at 110°C, Ni(NO3)2 and La(NO3)2 were added to distilled water.
Li, Methanation of carbon dioxide on Ni/ZrO2-Al2O3 catalysts：Effects of ZrO2 promoter and preparation method of novel ZrO2-A12O3 cartier，Journal of Natural Gas Chemistry. 20 ( 2011 ) 318–324 [2] N.S.
Adsorbent Materials for Carbon Dioxide Capture from Large Anthropogenic Point Sources, ChemSusChem. 2 ( 2009) 796 – 854 [5] M.M.
Chemical-looping combustion (CLC) for inherent CO2 separations - a review, Chemical Engineering Science. 63 (2008) 4433 – 4451 [6] R.
CO2 Methanation under Transient and Steady-State Conditions over Rh/CeO2-Promoted Rh/SiO2: The Role of Surface and Bulk Ceria Journal of Catal. 151 ( 1995 ) 111−124 [11] S.

Methods Material and technique used in DSSC fabrication is based on reference [9].
Maradin, Advantages and disadvantages of renewable energy sources utilization, International, Journal of Energy Economics and Policy, 11, (2021)
Jarial, A review on solar photovoltaic technology and future trends, International Journal of Scientific Research in Computer Science, Engineering and Information Technology 4.1, (2018) 227-235
Pranoto, A comparative study between titania and zirconia as material for scattering layer in dye sensitized solar cells, Journal of Physics: Conference Series, Institute of Physics Publishing, 1 (2018) 1742-6596
[12] Saxena, V., Singh, A., Prakash, O., Mahajan, Improved performance of dye sensitized solar cell via fine tuning of ultra-thin compact TiO2 layer, Solar Energy Materials and Solar Cells, 170 (2017) 127-136.

This research is funded by the Advanced Structural Materials for Next Generation Vehicles (ASM-NGV) Program of Natural Resources Canada.
(2007) The effect of solidification models on the prediction results of the temperature change of the aluminum cylinder head estimated by FDM solidification analysis, Trans Tech Publications, Switzerland, Materials Science Forum vols. 561-565, 1967-1970
H., Yamagata, H., Sahoo, M. and Kurita, H. (2009) The effect of the melt temperature and the cooling rate on the microstructure of the Al-20%Si alloy used for monolithic engine blocks, International Journal of Metalcasting (in-print)
[8] Kim, B., Chang, H., Lee, K. and Kim, C. (2007) Durability improvement of a cylinder heads in consideration of manufacturing process, International Journal of Automotive Technology, 8 (2), 243-248
[9] Kim, B., Egner-Walter, A. and Chang, H. (2006) Estimation of residual stress in cylinder head, International Journal of Automotive Technology, 7 (1), 69−74.

Recently, P(VDF-co-HFP) has received many special attentions as a promising material for polymer electrolytes because of its excellent properties [6-14].
Experimental Materials.
To estimate the compatibility of two materials, a single parameter, the relative energy difference (RED) is calculated from HSP of the two materials according to the following expressions.
A small RED value means a strong interaction or a good compatibility between the two materials.
A new method to determine the partial solubility parameters of polymers from intrinsic viscosity, European Journal of Pharmaceutical Sciences, 2005, 24, 229.

The diffusion of nitrogen into the interior of the material was determined by the thickness of the layer being modified.
Introduction Titanium alloys are the most widely used construction materials in various industries due to their inherent properties, i.e. high specific strength, corrosion resistance in many corrosive environments, non-magnetic properties, good heat resistance at the operating temperatures up to 500-600 °C [1, 2].
The depth of a hardened layer was determined from the hardness distribution curve to the value of hardness of the basic material.
Metal Science and Heat Treatment 7. 25 (2007) 25–29
Metal Science and Heat Treatment, 5 (1996) 28-31

The materials of hardmetal are milled in alcohol mixed with QSD, achieving a molecule dispersing slurry.
We choose the raw material of QSD according to their solution in alcohol.
The solvent of material slurry was eliminated in a drying cabinet.
These materials may all dissolve in alcohol with low or middle molecular weight ,and polar chemical bond such as ester or aether group.
Tang: Journal of Sichuan University of Science ＆ Engineering (Natural Science Edition) ( In Chinese ), Vol. 19（2006）, p. 30~33 [4] G.D.

Scandinavian Journal of Statistics.
International Journal on Hydropower&Dams.
Probability in Engineering and Informational Sciences.
Science in China Series E.
Journal of Hydrologic Engineering.

Since many of the pollutants are associated with suspended particulate materials in stormwater, SS (suspended solids) is of acknowledged importance in stormwater runoff treatment by BMPs (best management practices).
Materials and method Preparation of filter media.
On return to the laboratory, collected material was manually mixed and air-dried.
Aim: Journal of environmental engineering vol. 122, no. 1 (1996), p. 25~33 [6] S.
Lee: Material science forum vols. 510-511, (2006), p. 718~721.

Nowadays, the reinforcing materials in polymer composites are typically carbon fibers (CF).
Carbon fiber (CF) is a kind of non-metallic materials.
Experimental 2.1 Materials Poly (butylene succinate) (PBS) with a density of 0.91 g.cm-3 and MI of 4.5g/10 min (130°C, BIONOLLE 1903MD) was provided by Showa Co.
Journal of composite materials, 2009，26(3)：50-54
Materials engineering, 2005(11)：50-57