Search results

Materials Science Forum Vols. *** (2004) pp.865-870 online at http://scientific.net  2004 Trans Tech Publications, Switzerland A Hybrid Model for Tool Condition Monitoring and Optimal Tool Management Y.X.
Advances in Materials Manufacturing Science and Technology 866 Sub-model III is a decision-making model, in which the tool condition is calculated by fusing the results from Sub-model I and II to decide when the tool has reached the end of life and should be replaced.
The RMS Materials Science Forum Vols. *** 867 ratios of two sensors' outputs are shown in Fig.3 while the vessel is filled with water, engine oil 68 and magneto-fluid, respectively. 0 10 20 30 40 1 2 3 4 Ratio(%) Organic glass Main spindle spring AE sensor Magneto-fluid magnet According to the above results, a measuring set-up shown in Fig.4 is developed.
Materials Science Forum Vols. *** 869 Sub-model for Decision of Tool Condition.
Dornfeld: Journal of Engineering Industry Vol. 30 (1989), p. 199.

In this investigation a mild strength steel DC04 is used as sheet material.
Introduction Tribology is defined as the science of interacting surfaces at relative movement [1].
To measure the influence of surface roughness on disperse of CO2 in this lubrication system, four different sheet materials are tested.
The liquid CO2 acts like intermediate material, similar to the regular lubricant.
Schmidt, Dry Metal Forming: Definition, Chances and Challenges, International Journal of precision engineering and manufacturing - green technology, Vol.1, No. 1 (2014) 1-4

These properties concern the elastic-plastic behaviours of the sheet metal and rivet materials.
Blount: The Suitability of Aluminium as an Alternative Material for Car Bodies, Materials and Design, vol. 20 (1999), pp. 267-272
Sinha: Comparative Study of some Mechanical Connections in Cold Formed Steel, Construction and Building Materials, vol. 13 (1999), pp. 109-116
-R Pashby: Joining Techniques for Aluminium Spaceframes used in Autos, Part II-Adhesive Bonding and Mechanical Fasteners, Journal of Materials Processing Techniques, vol. 99 (2000), pp. 72-79
Aalberg: Self-piercing riveting process: an experimental and numerical investigation, Journal of Materials Processing Technology 171 (2006), pp. 10-20 [7] E.

Clarke, Materials Science and Engineering A, 246 (1998), p 180. 3.
Bonner, Materials Science and Engineering A, 340 (2003), p272. 6.
Baxter, Metallurgical and Materials Transactions, 33A (2002) p 3227. 9.
Materials Science and Engineering A, (2006), accepted for publication. 10.
Baxter, to be submitted to Materials Science and Engineering A.

These materials are addedto control the odor during the raising period.
Experimental Method Materials.
The used materials in this study were Chicken Manure powder (CM), struvite, and ash of EFB.
Nweke, Effect Of Poultry Manure And Mineral Fertilizer On The Growth Performance And Quality Of Cucumber Fruits, Journal Of Experimental Biology And Agricultural Sciences, Vol. 3, No. 4
Hazardous Materials journal,Vol. 169, (2009) Pp. 801–807

Experimental Materials.
Reneker: Journal of Electrostatics Vol.35 (1995), p.151 [2] E.
Wnek: Journal of Controlled Release Vol.81 (2002), p.57 [3] P.
Iwatsuki: Journal of Antimicrobial Chemotherapy Vol. 48(4) (2001), p.487 [5] S.M.C.
Giridev: Journal of Applied Polymer Science Vol.121 (2011), p.2893 [10] P.

Issue (i): the material capacity of the high strength stainless steel wire of non-pre-stressed SSWM-M is not fully utilized.
[J] Journal of Building Structures. 2003,24(6): 87-91,97.
Journal of Building Structures，2005, 26(2): 10-17.
Journal of Building Structures，2005，26(2):1-9.
China Civil Engineering Journal, 2007, 40(8): 1-7.

The mission of the WAI is to Develop guidelines that are widely regarded as the international standard for Web accessibility; support materials to help understand and implement Web accessibility; and resources through international collaboration The W3C published its first Web Content Accessibility Guidelines (WCAG 1.0) in May of 1999 for making online content accessible to people with disabilities.
The New England Journal of Medicine, 348 (25), 2526-2534
Journal of Nursing Administration, 23 (11), 24-34
[10] Paparella, S.S. (2007), “FMEA: a useful tool for risk identification and injury prevention”, Journal of Emergency Nursing: JEN (J Emerg Nurs), Vol. 33 No. 4, pp. 367-71
A Thesis Submitted to Institute of Management National Yunlin University of Science & Technology in Partial Fulfillment of the Requirements for the Degree of Doctor of philosophy in Management

A typical manufacturer spends 60% of its total sales on purchased items such as raw materials, parts, subassemblies and components.
Acknowledgement This research is supported by National Natural Science Foundation of China (71271103), Scientific Research Fund of Senior Technical Personnel of Jiangsu University(12JDG130).
Tien:Integration of artificial neural network and MADA methods for green supplier selection, Journal of Cleaner Production,18(2010),pp.1161-1170
[9] S.Opricovic , G.H.Tzeng: Extended VIKOR method in comparison with outranking methods,European Journal of Operational Research, 178(2007), pp.514-529
Chang:Applications of the extent analysis method on fuzzy AHP.European Journal of Operational Research, 95 (1996), pp. 649-655.

With the development of aircraft engine, higher requirement was put forward on turbine disk materials.
With the development direction of higher mechanical properties, higher reliability and larger size, it requires metallic materials to have a combination of temperature capability and mechanical properties [1-4].
Materials and Experimental Procedures Thermodynamic equilibrium of alloys with different content of W from 1 Wt. % to 13 Wt. % has been calculated using JMat-Pro software based on the Ni database.
Journal of Aeronautical Materials. 36(3) (2016) 27-39
Journal of Iron and Steel Research, International. 21(12) (2014) 1152-1157