Search results

Tian, The geosynthetic materials friction characteristic test analysis of south-to-north water transfer project, Water Sciences and Engineering Technology, 2 (2012) 58-60 [5] F.
Zhi, The direct shear friction test research of geosynthetic material interface, Journal of China & Foreign Highway, 3 (2006) 255-258

Selection of isolator parameter according to the Guangdong Science and Technology Co., Ltd.
As for the difference of additional layer’s material of the upper structure in a multi-earthquake, the interlaminar shears of response spectrum analysis have a little difference.
AIJ Journal of Structural Construction Engineering, n620, 2007: 43~ 49
Applied Mechanics and Materials, 2013, （2）:2091－2095.

Machining material is W18Cr4V.
Acknowledgements This work was financially supported by the Natural Science Foundation of Heilongjiang Province of China (No.
References [1] Zhang Zhihang, Guo Libin, Cui Hai: Applied Mechanics and Materials, Vol. 138-189(2012), p. 1251-1257 [2] N．Balakrishnan, Bruno Scarpa: Journal of Multivariate Analysis.

In the last years intensive work has been performed toward the make of high alloyed materials and steels that have competitive properties and mechanical indices.
The high alloyed with Cr steels find a wide application as wear-resistance material that is used in the conditions of strike wearing out.
Rachev, High-nitrogen steels - Metallurgy under of pressure, Bulgarian science academy, Sofia (1995), in Russian. 4.
Rassizadehghani, International Journal of Cast Metals Research, Vol. 19 (2), p. 323-329 (2006) 5.

Currently passive rubber damper mainly depend on compression and shear deformation of the rubber material to achieve absorption and consumption of vibration energy, although the type of damper’s structure is simple, the cost is not high, there are some limitations on the damping characteristics, especially on high frequency[1,2,3].
With development of MR fluid damper material technology, it causes widespread concern to use MR fluid damper instead traditional rubber damper [4,5].
Fig.6 Spectrum comparison when different damper are used on engine Conclusion MR fluid damper with new material is used as the damping device of the engine, its damping effect is indeed superior to the traditional rubber damper.
(Shanghai Science and Technology Literature Publishing House 1995)
[5]Changrong Liao, Niao Yu, Honghui Zhang, in: Calculation method on damping force of automotive magnetorheological fluid shock absorber, edtied by volume. 19 of China Journal of Highway and Transport( 2006).

Science, 850-853. (2013)
Canadian Journal of Forest Research, 33(8), 1557-1563. (2003)
JGISE: Journal of Geospatial Information Science and Engineering, 5(2), 63-70
International Journal of Remote Sensing, 38(8-10), 2150-2160. (2017)
Canadian journal of forest research, 26(7), 1228-1236. (1996)

Generally,chemical fertilizer is considered as a one of the most significant materials for increasing food production.
RHs are considered as renewable energy usable materials, which can create a way of green economy [5].
Methodology Materials and chemicals All the materials and chemicals were used without additional purification unless otherwise stated.
Natural Rubber Materials: Volume 1: Blends and IPNs (Vol. 7).
International Journal of Polymer Science, 2015. (2015) [5] N.

A new coagulant polysilicate iron and zinc (PSFZn) was prepared by using sodium silicate, inorganic acid, ferric chloride, zinc chloride as raw materials, the factors of (Fe+Zn):Si molar ratio, Fe:Si molar ratio, reaction temperature, reaction time and the dosage on coagulation performance were tested.
(3) The flocs produced by PSFZn were thick dense with high settlement rate, at the same time, PSFZn had the characteristic of obvious performance, simple preparation method , and inexpensive raw materials.
Acknowledgements This research was financially supported by The National Major Project of Science & Technology Ministry of China (Grant No.Z2008ZX07421-002) References [1] Yuezhou Zhang, Yaoguo Wu, Sihai Hu, Ying Tan: Technology of Water Treatment Vol.3(2008), p.1-6.
(in Chinese) [6] Li Gan, Zhaoping Meng: Journal of Safety and Environment Vol. 6 , No. 4(2006), P. 14-17.

Experimental Work Materials and Methods IN600, a Ni-based superalloy, was chosen as the substrate alloy in this work.
Khakpoura , M.Soltania, H.Sohia, Microstructure and High Temperature Oxidation behaviour of Zr doped Aluminide Coatings fabricated on Nickel-based Super Alloy, Procedia Materials Science (2015)
Sunesona, Oxidation Behavior of Hf-Modified Aluminide Coatings on Inconel718 at 1050°C , Journal of Coating Science and Technology, 2014, 1, 25-45
Stepanov, Oxidation Behavior of Refractory AlNbTiVZr0.25 High-Entropy Alloy Materials 2018, 11(12), 2526; https://doi.org/10.3390/ma11122526
Kim, Microstructural Evolution of Duplex Grain Structure and Interpretation of the Mechanism for NiO Scales Grown on Pure Ni – and Cr – Doped Substrate During High Temperature Oxidation, Materials Science and Engineering B76, (2000)pp. 173-183

Influence of Sputtering Power on the Structure and Photoelectric Property of Ga Doped ZnO Films Lei Wu1, a, Qingnan Zhao1,b, Gang Wu1,c and Dengkui Miao2,d 1 Key Laboratory of Silicate Materials Science and Engineering, Wuhan University of Technology, China 2 Jiang Su Xiuqiang Glasswork CO., Ltd.
Many researchers have pay attention to Doped-ZnO transparent conductive films, and have down many researches on a high transparency vis a wide spectral range, high carrier mobility and little light absorption materials.
It turned out that with the more power, the grain which participated in the growth of thin films can got more energy to migrated on the surface of the substrate materials.
Solar Energy Materials & Solar Cells, 2005,86:207–216
Journal of Non-crystalline Solids, 2010, 356:299-303