Search results

El Bouari, M.
Liu, et al., Preparation and characterization ofpermeable bricks from gangue and tailings, Constr.
Lei, et al., Investigation on the adsorption of Ni2+, Cu2+, Zn2+ by new montmorillonite based composite for water treatment, Nonmetallic Mineral. 37 (04) (2014) 78–80
Park, et al., Effect of partial replacement of sand with dry oyster shell on the long-term performance of concrete, Constr.

Table 1 chemical composition of 7050-T7451 aluminum alloy Al Zn Cu Mg Zr Mn Si Fe Ti Others Balance 6.7 2.5 2.3 0.12 0.10 0.12 0.13 0.06 0.15 Fig. 1 The experimental instrument Fig. 2 The measurements of surface roughness Results and Discussion Estimation of the Regression Model Parameters.
Jeong, et al: Journal of Materials Processing Technology, Vol. 113 (2001), p. 410-415
Mansour et al: Journal of Materials Processing Technology, Vol. 124 (2002), p.183-191
El Baradie and M.S.J.

Al-Mamun, S.
Al-Yasi, T.A.
Al-Talhi, S.M.
El-Megharbel, A new sterilization strategy using TiO2 nanotubes for production of free radicals that eliminate viruses and application of a treatment strategy to combat infections caused by emerging SARS-CoV-2 during the COVID-19 pandemic, Coatings, 11 (2021) 680

Bainitic quenched Boron steel 15 1100 200 100 50 10 700 400 300 500 600 900 800 1000 Ts M pa 1400 1300 1200 1500 El % EDDQ 20 3025 4035 45 BH, IF HSLA TRIP DP 50 Fig. 1.: The applicability of modern High Strength Steels. [4] Earlier MP- steels were named DP- steels ( dual phase steels ).
The high Al content is used to stabilize ferrite and obtain a consistent mixture of ferrite matrix, bainite and retained austenite.
C Mn Si S P Cu Cr Ni Al Nb Mo V Sample weight% DP 0,11 1,4 0,38 0,003 0,014 0,06 0,28 0,03 0,039 0,043 0,242 0,006 TRIP 0,2 1,7 0,35 0,008 0,112 * * * 0,5 * * * Thyssen TRIP 0,28 1,41 0,28 0,001 0,016 * * * 1,08 * * * Welded in 90-10% Ar-N Welded in 50-50% Ar-N Base M.
One of the possible reasons is that the nitrogen of shielding gas diffuses into melt at cooling and precipitates together with Al, and it is unable to diffuse so quickly into the partially unmelt HAZ.

(1) εel=D-1⋅σ (2) ε⋅νp=(1/η)((σ-σy)/σ*))p (3) where, έ is the total strain rate, ε-el is the elastic strain rate, ε-vp is the viscoplastic strain rate, is the elastic stress, η is the viscosity coefficient, and P is the viscosity index.
Chen et al, Deformation control and mechanism research on large-scale thin-wall cabin body castings of aluminum alloy, Foundry Technology. 34( 2013)1336-1339
Fu et al, Quenching process simulation and deformation prediction of ZL205 aluminum alloy large complicated cylinder workpiece, Aeronautical Manufacturing Technology. 20(2016)36-40 [7] Q.C.
Bai et al, Study on solidification contraction of aluminum alloys, Journal of Northeastern University (Natural Science). 36( 2015) 646-650

Chen et al. describes the laser-ablation plume into three regimes, 1) elastic scattering regime that is described by drag model close to the target, 2) a reactive collision regime that is described by blast wave model, and 3) a sound wave regime (free diffusion model) [23].
Zhang, et al.: Phys.
Wang, et al.: Science Vol.299 (2003), p.1719 [4] T.
El Zein, Y.

Soares et al. (2014) have simulated the mobilization of residual oil ganglia by the magnetic stresses generated in a ferrofluid.
Ryoo et al. (2012) use ferrofluid made of iron oxide nanorods that is sufficient to produce measurable displacement of the interface between fluid and a ferrofluid when exposed to an oscillatory magnetic field [11].
After double-annealing process at 1000°C and 1200°C for 2 hours, almost pure YIG nanoparticles formed as similar to the finding in Ristic et al. (2003) although a different chemical route was used in this work [17].
El Mir, M.

These results are in a good agreement with the previous study by Wahi et.al [4] Table 1 Fitted isotherm models for adsorption of Hg(II) on PAC.
Similar observation was reported by Zabihi et. al. [25] for removal of mercury by AC prepared from walnut shell.
El.
Al Khatib, & Y.

L o cate th e data record D isplay or edit th e m odel Y E n d E stablish the param etric m od el C reate th e too l inform aito n N Q u ery the to ol m aster m o del E xistence?
Stone and et al.: Computer-Aided Design, Vol. 40 (2008), p.801
Qin, et al.: Mechanical Science and Technology, Vol. 27(2008),p.1154
Wang and et al.: China Mechanical Engineering, Vol. 19 (2008),p.2160.

Wang et al. [13] have proved that the surface layers of black mirrors in ancient china were mainly composed of nanometer-sized particles of Sn1-x(CuFePbSi)xO2 with cassiterite structure.
Herrera et al. [17-19] have demonstrated the alteration of the tin amalgam mirrors and the formation of SnO2.
These values are in agreement with the results reported by Wang et al. [13, 33], who studied the presence of SnO2 in ancient Chinese black mirrors and also synthesized SnO2 particles.
El Vidrio. 3nd Ed., (CSIC publications, Madrid 2003)