Search results

The corresponding indices in sequence are (1 0 0), (0 0 2), (1 0 1), (1 0 2), (1 1 0), (1 0 3), and (1 1 2) based on Shatnawi et al., 2016 [14].
Proc. 2015, 1699, 040001 [14] Shatnawi, M., Alsmadi, A., Bsoul, I, Salameh, B, Alna'washi, G.A, Al-Dweri F, El Akkad, F, Journal of Alloys and Compounds, 2016. 655, 244-252.

Recent investigations by Rahim et al. [6] and Li et al. [7] on drilling of titanium alloys at higher speeds have indicated that peck drilling method and WC-Co spiral drill point are accompanied by a higher tool life and low cutting force.
El-Khabeery, S.M.

Al-Fadala, Recycling building demolition waste in hot-mix asphalt concrete: a case study in Kuwait, J Mater Cycles Waste 7 (2005) 112-115
O.C. 24/08 sobre el Pliego de Prescripciones Técnicas Generales para obras de carreteras y puentes (PG-3).
Parte 12: Determinación de la sensibilidad al agua de las probetas de mezcla bituminosa”.

For example, Srinivasan et al [2] found that the urinary citrate excretion (601±84 mg/24h) of control group is obviously higher than patients of uric acid stones, calcium oxalate (CaOx) stones and calcium phosphate stones, the latter three are 415±43, 429±58 and 492±52 mg/24h, respectively.
As Hess et al [12] shown, citrate can not only enhance the inhibition of normal Tamm-Horsfall protein (n-THP) on CaOx crystal aggregation, but also change the promotion effect of abnormal stone former Tamm-Horsfall protein (SF-THP) into inhibition on CaOx crystal aggregation.
El-Shall.

However, Manshor et al (2016) pointed out that the pattern peak is visible at the angle of XRD in between 24o to 37o [15].
El-Maghraby, M.
Hong, Effect of multiple pressures by magnetic pulsed compaction (MPC) on the density of gas-atomized Al-20Si powder, Powder Technology 224 (2012) 360–364

Arul et al [7] found that tool wear reduces as feed rate increases from 0.04 to 0.2 mm/rev when fibre composite laminates were drilled using High Speed Steel (HSS) drills.
According to Jia et al. [15], cutting speeds from 20 to 90 m/min and feed rate below 0.5 mm/rev are normally chosen for drilling of the CFC materials.
El-Gizawy, A.

This implies that RHA is a good pozzolana that can aid the promotion of the cementitious compounds configuration with cement hydration reaction products which is in agreement with Adeyanju et al. [4] and Ogbiye et al. [16].
El-sawwaf, M.

Furthermore, content of Al, Co, Mn, Ni, La, Ce, and Nd are also altered.
Abd-El Motaleb: Waste Management (2007) p.1-9
Montgomery: Second Edition (1984) [4] Luquan Ren,et al.: Chinese Journal of Mechanical Engineering,1999,vol. 12(2) [5] M.V.

Portlandite is consumed by FA or MK to form C-S,Al-H.
Figure 7: Proportion of Al species obtained by 27Al MAS NMR.
Al(IV): aluminum substituted for silicon in C-S-H chains and residual anhydrous cement.
Al(V): aluminum substituted for calcium in the C-S-H interlayers or present in non-hydrated phases or in MK.
[4] El-Hachem R., Rozière E., Grondin F., Loukili A., New procedure to investigate external sulphate attack on cementitious materials, Cement and Concrete Composites. 34 (2012) 357-364

Gantzer, A.L.
Al-Abed, J.
El-Mehaisin: Arch.
Murphy, A.L.
Gantzer, A.L.