Search results

Experiment Materials.
Nishihara, Development of Friction Stir Forming, Materials Science Forum, 426-432(2003) 2971-2978
[5] T.Nishihara, K.Yamamura, Local Manufacture of MMC Using FSW, Materials Science Forum 539-543 (2007) 3733-3738
Charit, Friction stir processing: a novel technique for fabrication of surface composite, Materials Science and Engineering A341 (2003)307-310
Fujii, T.Nagaoka, M.Fukusumi, Effect of friction stir processing with SiC particles on microstructure and hardness of AZ31, Materials Science and Engineering, A433 (2006) 50–54

Preparation of compound filter materials Row material.Water Natural clinoptilolite: Jinan Xinda Trade act as purchasing agency, the main chemical compositions is in table 1;The pore-forming agent: laboratory to configuration;Adhesive: laboratory to configuration.
Compound zeolite filter material Test method Materials and equipment.Lightweight ceramsite: average grain diameter 3-4mm,Ji'nan Xinda Trade act as purchasing.
References [1] Riqiang Li,Songhui Li,Jiangdi Wang.Journal of Environmental Sciences,163(2009),p. 804-808
Journal of Food Engineering, Vol 63 (2004), p. 467-472
[3] Langmuir I.Journal of American Chemistry Society, Vol 40(1918),p. 1361-1403.

Thermal protection materials are required to preserve the metal components of motor that suffer severe heat load.
Introduction Polymeric Ablative Materials (PAMs) are used to provide insulation to Solid Rocket Motors [1-4].
Lin W S[5] studied the quasi-steady solutions for the ablation of charring materials.
Test Methodology To get the thermo-ablative properties of EPDM thermal protection material, the materials were tested through a connected pipe test facility.
[2] Ahmed AF and Hoa SV: Journal of Composite Material.

Modeling for Materials and Logistics Optimal System in JIT Flexible Manufacturing Yanhong Wanga, Tianying Xub and Zhongda Tianc Department of Information Science and Engineering, Shenyang University of Technology, Shenyang, China, 110870 awangyh_sut@163.com, bxutianying3@126.com, ctianzhongda@126.com Keywords: Logistics Optimal; Materials Management; Flexible Manufacturing System; Just In Time.
The LCs works as a supervisory controller for the material flow in the flexible production processes, including all materials, raw materials, work in processes, finished products, in the shopfloor.
Information related to material requirement and other static data was send to the workshop by MPs, and then vehicles start to transport materials according to planned routes and expected time.
While the LCs works as a supervisory controller for the material flow in the flexible production processes, related to raw materials, work in processes, finished products, and so on.
The international journal of advanced manufacturing technology, Vol. 26, (2005), p. 1421-1428.

Multi-objective programming approach for routing hazardous materials.
Designing a road network for hazardous materials transportation.
Transportation Science 38(2), p. 188-196
Designing a road network for hazardous materials shipments.
Management Science 54(1), p. 29-40.

Here, identified performance indicators for materials management are presented.
It shows the value of unused materials that need to be returned or restocked.
This follows from conventional materials management being carried out using bill-of-materials, inventory data and master production schedules to determine time-phased plans for components and raw materials required for production [24].
Bell, Measuring effectiveness of materials management process, Journal of management in engineering. 11,6 (1995) 26-32
Raman, An econometric analysis of inventory turnover performance in retail services, Management Science. 51,2 (2005) 181-194

Methodology Materials.
Virgin plastic pellets are crude oil-based materials [33], therefore these raw materials are non-renewable.
Martin: Testing of Materials, In C.A.
Materials Science Forum, Vol. 936 (2018), 116-120
Matei, et al.: Recycled polypropylene improved with thermoplastic elastomers, International Journal of Polymer Science, (2017), 7525923

Functionally graded materials (FGM) are materials with varying electrical, chemical, mechanical, magnetic, thermal properties over the volume of the bulk material.
Bilgili, Improvement of thermal efficiency in computer heat sink using functionally graded materials, Communications on Advanced Computational Science with Applications, 2014 (2014) 13 Pages
Jaluria, Numerical simulation of thermal transport associated with a continuously moving flat sheet in materials processing, Journal of Heat Transfer, 113 (1991) 612-619
Jaluria, Forced convective heat transfer from a continuously moving heated cylindrical rod in materials processing, Journal of Heat Transfer, 116, (1994) 724-734
Lopez, Convection-radiation from a continuously moving, variable thermal conductivity sheet or rod undergoing thermal processing, International Journal of Thermal Sciences, 50 (2011) 1523-1531

Knésl1,c 1 Institute of Physics of Materials, Academy of Sciences of the Czech Republic, Žižkova 22, 616 62 Brno, Czech Republic a nahlik@ipm.cz , b hutar@ipm.cz, c knesl@ipm.cz Keywords: bi-material interface, residual stress, plasticity-induced crack closure, critical stress.
Journal of Fracture, 12 (1976), p. 52
Journal of Fracture, 73 (1995), p. 1
Journal of Fracture, 48 (1991), p.
Science 28 (2003), p. 620

This decrease suggests that the composite materials exhibit increased flexibility compared to Neat NR.
Fan, Polymer dielectrics for capacitive energy storage: From theories, materials to industrial capacitors, Materials Today. 68 (2023) 298–333
Saetung, Synthesis and characterization of novel natural rubber based cationic waterborne polyurethane: Effect of emulsifier and diol class chain extender, Journal of Applied Polymer Science. 135 (2018)
Assiri, Optimization of structural, dielectric, and magnetic properties of nanocrystalline copper doped spinel ferrites, Materials Science and Engineering: B. 297 (2023) 116739
Asath Bahadur, Impact of nickel substitution on structural, dielectric, magnetic, and electrochemical properties of copper ferrite nanostructures for energy storage devices, Journal of Colloid and Interface Science. 653 (2024) 917–929