Search results

A large body of research has been devoted to the design and fabrication of cooling channels, found in the recent review studies of Feng et al. [8] and Kanbur et al. [9].
Marin et al. [17] designed parallel and series patterns for CCCs of the injection-moulded component.
Lu et al. [18] also compared the effect of conventional baffle channels and CCCs on cooling time and residual stress.
Z., Gondro, J., Sharif, S., Al Bakri Abdullah, M.
M., Mohd Zain, A., El-Hadj Abdellah, A., Mat Saad, M.

[3] J Van Haveren, EL Scott and J Sanders:.
Simonetti, Ryan M. et al.: SCIENCE.
Lucas, et al.: Clean Air Vol 7 (2006), p. 363
Yang, et al.: Bioresource Technology Vol. 100 (2009), p. 2444
Minkova, et al.: Fuel Vol. 73 (1994), p. 1718

Zhang, et al.
[6] Liu Q, Zhang L, Liu J, et al.
[16] Walker LS, Corral EL, Parthasar T.
Schmidt-Wimmerb, et al.
[20] Padmavathi N, Ray KK, Subrahmanyam J, et al.

Singh et al. [1] found in all of spindle speed, thrust force is increased accompany with increasing the feed rate that cause to boost delamination.
According to the conclusions Abr ̃ao et al. [6] Tungsten carbide tools are preferred when drilling at higher cutting speeds and, in contrast to metals, also at higher feed rates.
Rubio et al. [8] have been also expressed, delamination factor enhanced when the feed rate increased but the higher spindle speed could be decreased the delamination factor.
Singh et al. [9] have been expressed that the thrust force depends on the drill point angle.
El-Sonbaty, A.I.

Biskra province is limited to the North by Batna province, to the South by Ouargla and El Oued provinces, to the East by Khenchela province, and to the West by Djelfa and M’Sila provinces (Fig. 1).
In fact, each Al3+ ion requires 3 OH- ions to pass to the Al(OH)3 form, coming from bicarbonates and the water itself in addition, H+ protons were released and subsequently, the pH also was decreased.
At pH values higher than 7, the aluminate radical Al(OH)4- predominates in the pH range from 8 to 10 and at higher pH values changes into Al(OH)52- [35,36].
Effect of solution chemistry on coagulation with hydrolyzed Al (III) signification of sulfate ion and pH.
[40] Abid B.A., Brbooti M.M., and Al-Shuwaiki N.M. (2011).

Based on an earlier study by Grunau et al. (1987), shale and evaporite caprock are the typical seal due to their mechanical properties and porosity [11].
Another study by Khazaei et al. (2017) evaluate caprock integrity during co2 injection at the Weyburn CCS project in Canada using a reservoir-geomechanical model.
Acknowledgment The authors would like to thank Universiti Malaysia Pahang Al-Sultan Abdullah and Rock Flow Dynamics for their support in this research.
[19] Lerer and Kevin, “Gypsum, Calcite, and Dolomite Caprock Fabrics and Geochemistry from the Gypsum Valley Salt Diapir, Paradox Basin, Southwestern Colorado,” ETD Collection for University of Texas, El Paso, 2017
Martens et al., “CO2 Storage at the Ketzin Pilot Site, Germany: Fourth Year of Injection, Monitoring, Modelling and Verification,” Energy Procedia, vol. 37, pp. 6434–6443, 2013, doi: 10.1016/j.egypro.2013.06.573

Luo et al. prepared a nanofluid made up of graphene-based amphiphilic nanoparticles in research.
In another study by Jeon et al. prepared a functionalized two-dimensional (2D) Janus-graphene nanosheets.
Al-O has stretching modes in the range of 1200–700 cm1, while bending modes dominate in the region of 1500–600 cm1.
Aliu, et al., "Graphene: outlook in the enhance oil recovery (EOR)," Journal of Molecular Liquids, vol. 321, p. 114519, 2021
El-Diasty and A.

Soil sample extraction and clean up were carried out according to the methods of USEPA 3540C and references described in the papers of Mai et al. [16] and Chen et al. [17].
For example, Hurst et al. [13] reported that the volatilization of 14C-pyrene was less than 0.3% over a 70-day incubation period, and Šašek et al. [24] also stated that the amount of volatile PAHs was below the detection limits over a 54-day composting period.
This result is in agreement with the findings of Leonardi et al. [23].
Mueller and E.L.
[5] A.L.

The geometry of a system of two tilted lattices in the current model is similar to that used by Lee et al. [31].
Shimomura et al. [18] reported MD simulation of a tensile test on a single crystal Cu thin film.
Gao et al. [20] and Lu et al. [21] conducted MD simulations of propagation of Mode I crack in bcc single crystal iron samples.
Gao et al. concluded that the initial lattice orientation significantly affects the behaviours of the crack growth.
Thus the behaviours of crack opening from simulation results of Farrisey el al. [19] can be qualitatively compared with results in this paper.

In this way, Malzbender et al [20] obtained an average interfacial toughness of 0.18 MPam0.5 for their hybrid coatings which falls into the range determined previously based on analysis by He et al [21].
Another adhesion model based on equilibrium theory and the solution for the deflection of a centrally loaded disc was proposed to deal with the same phenomena by Hainsworth et al. [37].
Marshall et al [43] proposed a model to relate the toughness of brittle bulk materials to the depth where lateral cracks occur and the crack driving force Pr due to the residual stress during unloading.
Here the hardness and elastic modulus are composite parameters resulting from the contribution of coating and substrate which can be estimated based on an energy-based model developed by Bull et al. [44-46].
El-Mansy, B.