Search results

Firstly, imbalance due to the motor's position affecting the center of mass can lead to undesired slipping during robot movement[6].
On inclined or uneven surfaces, slipping caused by imbalance can cause the robot to deviate from a straight path, affecting its ability to follow a desired trajectory.
Furthermore, the utilization of 3D printing technology enabled rapid prototyping and customization of components, facilitating the implementation of design iterations and fine-tuning of mechanical properties.
It can exhibit relatively slow response times compared to other sensors, and its accuracy can be affected by factors such as temperature variations and external interference.
However, it's essential to consider potential factors that may influence these results, such as surface roughness, traction, and adhesion properties.

Smith et al. [12] analyzed factors affecting the adoption of timber as a bridge material, where more then 20 criteria were accounted.
Factors such as prefabrication level, drying, transport, knowledge, and experience in using elements affected the estimate of the construction time criterion.
Being a natural raw material, timber represents one of the best choices for energy efficient construction, since it also functions as a good thermal insulator, has good mechanical properties, and ensures a comfortable indoor living climate.
[3] Assefa, G. et al.,: Quality versus impact: Comparing the environmental efficiency of building properties using the EcoEffect tool.
[12] Smith, R., Bush, J.R., Schmoldt, L.D.: A hierarchical model and analysis of factors affecting the adoption of timber as a bridge material.

Currently, many investigations have been carried out on the microstructure, properties and processes of the Al-Zn-Mg-Cu alloy thick plates.
Mechanical tests.
The tensile properties and fracture toughness results of experimental alloy plates in L-T and T-L orientation are shown in Table 1.
Conclusions The tensile properties, fracture toughness and fatigue properties of T7451 Al-Zn-Mg-Cu alloy thick plates vary in different orientations or plate thicknesses.
The samples in L-T orientation possessed better mechanical properties, higher fracture toughness and fatigue resistance than those in T-L orientation.

Microstructure and Properties of Laser Cladding Co-based Alloy Layer X.R.
Even, some special microstructure with excellent physical and chemical properties also could be formed [4-9].
Microstructure and properties of cobalt-based alloy coating on tool steel surface prepared by laser cladding.
Relationships between tensile and fracture mechanics properties and fatigue properties of large plastic mould steel blocks.
Research on Microstructure and Properties of In-situ Synthesized Metal Ceramic Composite Coating by Laser Cladding.

Depending on operating conditions they must have specific electrical properties or defined mechanical properties.
The insulating properties remain.
In previous studies it has been found that many factors influence the formation of the composite [7,8].
Furthermore, the plurality of the parameters during the manufacturing affecting the composite properties.
For the suspension preparation particularly the kind and amount of additives are influencing factors.

The aim of this study was to evaluate the underlying factor affecting fatigue crack growth rate in the stage II region.
Therefore, fatigue behavior of this alloy has been subjected to numerous studies to improve fatigue material properties [3] [4].
The addition of Zr to Al alloys has exhibited positive effects on microstructure via grain refinement and improvement in the mechanical properties [9].
Thompson, Metallic Materials Properties Development and Standardization (MMPDS) Handbook, NTIS Virginia Scientific Report (2003)
Farrokhpour, Effect of laser shock peening on surface properties and residual stress of Al6061-T6, Optics and Lasers in Engineering Vol. 77 (2016), p. 112

Introduction The diamond-like carbon (DLC) coating is a collection term for a large class of amorphous or amorphous nanocrystalline composite carbon films with different properties.
Liquid Solid Liquid Solid Fig.1 (a) Water contact angle less than 90°: hydrophilic; (b) Water contact angle greater than 90°: hydrophobicity a b The investment works [2-4] found that water contact angle is decided with two factors: the element composition and the micro-topography of surface.
In addition, the increasing in the roughness interfered with the affecting of surface energy for alcohol contact angle.
But the interfering not interfere the affecting of surface energy for water contact angle, so the value of angle increase as roughness increase, as show in fig.12 (f).
Wang, et al., Fullerene nanostructure-induced excellent mechanical properties in hydrogenated amorphous carbon, Applied Physics Letters. 91(2007)(14):141902-3

In general, the real-time temperature curves aren’t exactly consistent with the required one due to the influence of uncertainty factors in site, and the quality of magnetic materials may be affected consequently.
The similarity between the real-time process curves and the designed one directly or indirectly reflects the control performance and the product properties.
Given a product quality is affected by process variables.
The method is applied in sintering of magnetic materials in this section to evaluate the control performance and the product properties.
The characteristics of process and the shape of a curve are two key factors for the similar evaluation of process curves.

For the assessment of mechanical properties of rubber compounds, tensile and hardness tests were performed.
Mechanical Properties of Compounded Rubber.
Table 4 summarizes the mechanical properties of the compounds filled with CB and AC.
Mechanical properties of rubber compounds filled with CB and AC.
Mechanical properties of activated carbon (AC) coconut shell reinforced polypropylene composites encapsulated with epoxy resin.

Factors that affect syngas are the type of biomass (chemical, physical, and morphological properties) and the gasification process (type of gasifier, temperature, gasification agent, and ratio equilibrium (ER)).
The characteristics of syngas as the output of biomass gasification maybe affected by various factors which further may also affect the performance of the syngas fermentation process.
It is the goal of this paper to review the factors affecting the characteristics of syngas and the corresponding effects on the syngas fermentation performance.
These factors may affect fermentation performance and the corresponding bioethanol productivity.
Critical factors affecting the integration of biomass gasification and syngas fermentation technology.