Search results

Compared to the results reported by Sarkar et.al (2020) of 530.6 Fg-1 at 0.5 Ag-1 current density [6], our results were smaller.
El-Sakhawy, B.
Al Sharie, M.
Al Khasawneh, F.
Al Jaiuossi, “Pearl-white gallstones: A report of a case and a chemical analysis by FTIR and XRD,” Int.

Elemental analyses were performed on Elementar Vario EL, or Carlo-Erbo 1106 Elemental analysis apparatus.
[3] Carmelo Puglia, Rosanna Filosa, Antonella Peduto, Paolo de Caprariis, Luisa Rizza and Francesco Bonina,et al.
[4] Zhang Shoufang, Gao Wenfang, Zheng Hong, Wang Guiqin, Lai Li, Gao Huaimin, et al.
Chem., 1972, 37 (23), 3618–3622 [7] Hiroyuki Nakamura, Taikou Usui, Hirokazu Kuroda,† Ilhyong Ryu, Hiroshi Matsubara, Shinji Yasuda, et al.
[8] Santosh Bhor, Gopinathan Anilkumar, Man Kin Tse, Markus Klawonn, Christian Döbler, Bianca Bitterlich,et al.

After the distillation process, a heavier product is obtained, known as bitumen (Antunes et al., 2015).
When crude oil is heavier, bitumen yields tend to be higher (Porto et al., 2019).
For example, a study found that Polyphosphoric acid (PPA) was defined to be a means of stabilizing PMBs in their formulations (Giavarini et al., 1996).
Silicon tetrachloride is pyrolyzed in a flame, or quartz sand is vaporized in a 3000°C electric arc to produce fumed silica (Gagne et al. 2005).
[3] Aydoğan, C.; El Rassi, Z.

Gein et al. [17] investigated the influence of the addition of 1-3 at.-% Molybdenum on the microstructure of the alloy and its mechanical properties.
Chen et al., Li et al., and Feng et al. [7-9] provide overviews of the fatigue relevant mechanisms in HEAs, including dislocation-evolution, deformation nano-twinning and twinning induced plasticity (TWIP) [7, 9].
Weaver, Editorial: Dual-Phase Materials in the Medium and High Entropy Alloy Systems Al-Cr-Fe-Ni and Al-Co-Cr-Fe-Ni, Front.
Zhang, Enhancing bending fatigue resistance of the CoCrFeMnNi high-entropy alloy thin foils by Al addition, Mater.
El Haddad, T.H.

El Moutchou, H.
Qin et al., “The thermal runaway analysis on LiFePO4 electrical energy storage packs with different venting areas and void volumes,” Appl.
Ma et al., “Research progress on early warning method and suppression technology of thermal runaway of lithium battery,” J.
Peng et al., “Dynamics of multidimensional signals in lithium-ion battery during thermal runaway under various oven temperatures,” J.
Rahmani et al., “Driving the future: A comprehensive review of automotive battery management system technologies, and future trends,” J.

El-Hag3e 1Mechanical Engineering Department, Faculty of Engineering, University of Benghazi P.O.Box 1308, Libya 2Material Science and Engineering Department, Faculty of Engineering, Omar Al-Mukhtar University, Libya 3Chemistry Department, Faculty of Science, University of Benghazi P.O.Box 1308, Libya aMohamed.melad@uob.edu.ly, *bMohamed.almalki@uob.edu.ly, cfarag.shuaeib@uob.edu.ly, drafaa.esmaael@omu.edu.ly, eMohamed.elhag@uob.edu.ly Keywords: Duplex stainless steel, TIG welding process, N2 shielding gas, Response surface methodology, Mechanical properties, Critical pitting potential.
Similarly, Baghdadchi et al., [9] investigated the impact of shielding gases and laser reheating while welding 1.5 mm-thick DSS.
Korra et al., [16] researched to optimize the activated TIG (A-TIG) welding process for welding SDSS alloy 2507 using RSM.
Mondal et al., [19] identified the most effective TIG welding parameters for DSS in order to produce the required mechanical characteristics for the weld.
Sharma, “Study of Mechanical Properties in Austenitic Stainless Steel Using Gas Tungsten Arc Welding (GTAW) et al Int,” J.

However, it is difficult to produce fine, fully nitrided powders because during the reaction the Al powder can form large aggregates due to its melting point (660 o C) being lower than the nitridation temperature (≥800oC) [25].
In addition, AlN formation occurs first on the surface of the Al particles inhibiting the diffusion of the nitrogen to the unreacted metal.
As for the chemical vapour infiltration process, extended reaction times are therefore required to allow adequate diffusion whilst intermittent grinding steps are generally necessary to break the agglomerates and expose fresh surfaces of unreacted Al [26].
[30] Palaith D., Silberglitt R., Wu C.C.M., Kleiner R. and Libelo E.L., in Microwave Processing of Materials, Eds.

Steel C Mn Si Ni Cr Mo Cu Al S P Ce 42CrMo4 0.41 0.72 0.26 0.17 1.0 0.17 0.16 0.024 0.001 0.006 - 42CrMo4Ce 0.404 0.77 0.22 0.189 1.03 0.165 0.16 0.015 0.0033 0.007 0.067 After removing from the plasma furnace, the steel samples were vertically cut along a center cross section and mounted.
Guo et.al. [15], revealing that a wide variation in concentration of dissolved Ce did not produce any effects on grain sizes in solidification structure of steels.
El-Kaddah, T.
Nagaumi, Prediction of porosity contents and examination of porosity formation in Al-4.4%Mg DC slab, Sci.

Fussell et al. [1] developed a 5-axis virtual machining environment for discrete simulation of sculptured surface machining which aims automatic feedrate selection along the toolpath via mechanistic modeling of cutting forces.
Bailey et al. 2] proposed a generic mechanistic cutting force model for simulating multi axis machining of sculptured surfaces.
This article extends the modeling of 3-axis ball-end milling presented by Erdim et al. [5, 6] into mechanistic modeling of 5-axis ball-end milling.
El-Wardany, P.

Gertsik, et al.
El-Shennawy, O.
Mikhailov, et al.
Molochkov, et al.