Search results

With the development of science and technology, tunable optical fiber system will be bound to a rapid development and wide application [4].
System Implementation Material Selection of the System.
Fig.7: OTDR photo of access fiber of 2km+4km Conclusions This paper has presented a tunable optical fiber system from material selection, design and test.
“Optical-signal-processing device based on waveguide-type variable delay lines and optical gates”, Journal of lightwave technology, 2006(24), 2593-2061

Acknowledgement This study was carried out under the state assignment of the Ministry of Education and Science of Russian Federation for 2014-2016 (research work № 8.2500.2014/K).
Korepanov, Evaluation of the effect of LED-lamp spectral content on the development of greenhouse tomato, Key Engineering Materials. 685 (2016) 482-486 [7] A.N.
Kruglikova, Study of spectral characteristics of single leaves of plants (in Russian), Russian Physics Journal. 55-6/2 (2012) 158-162.

Akira, Fundamental Formulation of Airship Performance and Flight Dynamics, Institute of Space and Aeronautical Science, University of Tokyo Report No. 536, December 1975
Muhamad, Cost Analysis of a Hybrid Airship Vehicle for Cargo Delivery, Applied Mechanics and Materials Vols. 465-466 (2014) pp. 373-378 [8] K.S.
Song, Flight Performance Analysis of Hybrid Airship: Revised Analytical Formulation, Journal of Aircraft Vol. 47, No. 4, July-August 2010

Materials Nanoparticle.
Nanofluid for Enhanced Oil recovery, Journal of Petroleum Science and Engineering

The incorporation of DID concept and risk insight into deterministic based safety inspection has not been well studied so far since the regulatory safety inspection was developed depending on each country’s specific regulation In general understanding, PRA is described by the series of event trees (ET) that get initiated from an initiating event; therefore, it is essential to associate the relationship conceptually between the 3 levels of PRA with the 5 levels of DiD as define by IAEA [2] in Fig. 2 Fig. 2 Relationship between PRA and DID [3] To ensure the safety of nuclear power plants, the control of reactivity, removal of heat from the core, and restriction of radioactive materials should be performed.
[8] Rahman Khalil Ur, Jinsoo Shin, Muhammad Zubair, Gyunyoung Heo, and Hanseong Son, 2013, “Sensitivity Study on Availability of I&C Components Using Bayesian Network” Science and Technology of Nuclear Installations [9] M.
Khan, (2011) “Calculation and Updating of Reliability Parameters in Probabilistic Safety Assessment” Journal of Fusion Energy [10] Saud BinKhadim, Muhammad Zubair, (2019) “calculations of risk parameter for safety injection system (SIS) in APR1400, in case of large LOCA” The Proceedings of the International Conference on Nuclear Engineering (ICONE) 2019.27:1381.

High cycle fatigue tests were carried out by MTS 322.41 electro-hydraulic universal materials test frame.
Fig. 6 shows the installed sample during the examination in the materials testing equipment.
Fatigue & Fracture of Engineering Materials & Structures 34.1 (2011): 46-52
Materials, design, and manufacturing for lightweight vehicles.
Fatigue & Fracture of Engineering Materials & Structures 31.9 (2008): 766-776

These operations involve machining aero-structural components that are comprised of different materials, resulting in what is known as a hybrid joint.
Fig. 3 (a) shows a bar chart of the cutting times of five different sample tools for various materials.
In some cases, certain materials can be repeated along a hole, making them the ones containing more width drilled.
Additionally, titanium has the lowest cutting length, even though it has the highest accumulated cutting time among the materials considered.
(a) (b) Fig. 3: Normalize total cutting time (a) and cutting length (b) for different tools and different materials.

In recent years, with emerging new technologies and new materials, technology and equipment for executing vacuum preloading technique have been greatly improved, providing fundamental conditions for the research and development of the underwater vacuum preloading technology to improve soft soils in tidal zones.
Dredging, pile driving building of cast-in-situ piles and placing of fill materials were carried out simultaneously with the implementation of underwater vacuum preloading and the stability of the slopes was ensured. .
Chinese Journal of Geotechnical Engineering, 2007（5）: 644-649
Tianjin construction science and technology, 2006,16(B07)：45-49
Chinese Journal of Rock Mechanics and Engineering, 2006(s2): 3490-3494.

More advanced systems are based on glass-ceramic-materials [18].
The aim of the study is to investigate, if MCISPs, based on glass-ceramic-materials, could be used for packaging application.
Material and methods.
Trends in Food Science & Technology 21 (2010), pp. 117–128
Sethi, Flexibility in Manufacturing: A Survey, The International Journal of Flexible Manufacturing Systems 2 (1990), pp. 289–328

Jönsson2,c 1Department of Materials and Manufacturing, School of Engineering, Jönköping University, Sweden 2Department of Material Science and Technology, School of Industrial Engineering and Management, KTH Royal Institute of Technology, Sweden apeter.svidro@ju.se, battila.dioszegi@ju.se, cparj@kth.se Keywords: lamellar graphite iron, volume change, thermal analysis Abstract.
The material of the sample holder is usually sand and the investigated alloy is usually cast into a mold.
The thermal field is also heavily correlated to the material of the sample holder, since this is the medium that transports away the heat.
As it was mentioned above, in the case of all research units this material is the sand.
Kohler, Metal and Mold Wall Movements During Solidification of Cast Iron, Cast Metals Research Journal AFS 9 (1973) 20–30