Search results

Parish3,e and Tongguang Zhai1,f * 1Department of Chemical and Materials Engineering, University of Kentucky, 177 F.
China 3Microscopy Group, Materials Science & Technology Division, Oak Ridge National Laboratory, 1 Bethel Valley Rd., Building 4515, Rm. 191, Oak Ridge, TN 37831-6064, USA agongwang.zhang@uky.edu, bzhanghai888jp@yahoo.cn, chanyi7742@163.com, dxu_y@sinr.cn eparishcm@ornl.gov, ftongguang.zhai@uky.edu Keywords: Al-Mg-Si-Cu aluminum alloy, Mn-containing dispersoids, homogenization, recrystallization, Mn content.
Zhai: submitted to Journal of Alloys and Compounds (2016)
Gottstein, Physical Foundations of Materials Science, Springer, Berlin (1996).

However, in the energy use of a building over its whole life cycle the embodied energy of construction materials play a major role.
Besides the amount of the materials - which is described by the geometry - the construction sets (the material types) make the biggest influence on the embodied energy of the house.
In spite of the high variety of available materials, only a few sets are assembled, namely those which wereTable 3: Variables, that define the evaluated variants.
The number of replacements was calculated by the division of the reference service period by the lifetime of the construction materials.
Furthermore, A4 and C4 modules were also covered, as average values assigned to the materials.

Seibt2 1Institute of Solid State Physics, Russian Academy of Sciences, 142432 Chernogolovka, Russia 2Georg-August-Universität Göttingen, IV.
Acknowledgements The work was supported in part by research program “Physics of novel materials and structures” of Russian Academy of Sciences and by the President Grant NSh-884.2014.2.
Vanhellemont, Formation Energy of Intrinsic Point Defects in Si and Ge and Implications for Ge Crystal Growth Electronic Materials and Processing, Journal of Solid State Science and Technology, 2 (2013) 104-109

Materials and methods The collection of samples and disposal Between 17th and 19th, August, 2005, two cores (SY01, SY02) were collected in the core area of Yancheng red-crown crane National Natural Reserve (Xinyanggang in Sheyang County); surface samples were collected every 20m along the cross-section from the west to the east, 220 samples in all, the sampling locations refer to Figure 1.
Learn from Northern-Jiangsu heavy metal deposition law, the heavy metal deposition was mainly controlled by clay content and material source in the sediment, and was positively correlated with clay content.
Bulletin of the New Jersey Academy of Sciences, Vol. 33 (1989), p. 39-43
GEO Journal, Vol. 2 (1969), p. 108-118
Coastal and Shelf Science, Vol. 53 (2001), p. 259-274

Formation of Microstructure during Sub-Zero Treatments of Chromium and Chromium-Vanadium Ledeburitic Steels JURČI Peter Faculty of Material Sciences and Technology of the STU in Trnava, J.
Thus, the sub-zero treatment transformed from the "black-art" to the accepted topic of science.
In addition, Gavriljuk et al. [7] used powder metallurgy steel while conventional cast and wrought materials were used in other cited works.
Pendray, Cryoprocessing of Materials: A Review of Current Status, Mater.
Trnava: Faculty of Materials and Technology, Trnava, 2015

Florence, “Titanium Armor Plate,” Advanced Materials and Processes, Vol. 160, No. 9, September 2002, 35–37
Fray, The Minerals, Metals & Materials Society, Warrendale, PA, 2004, 135–143
Smugeresky, The Minerals, Metals & Materials Society, Warrendale, PA 2005, 267-280
Hatch, “Single-Melt PAM Processed Forged Ti-6Al-4V Bell Housings for Lightweight 155mm Howitzer,” in Application of Materials Science to Military Systems - CD Volume, Edited by D.
[20] “Materials Properties Handbook: Titanium Alloys,” R.

Firstly, providing material source for slope failures of the loess.
Human engineering, economic activities, including irrigation, and road construction, building materials digging and living and filling with soil, spoil, building loads and so on.
Journal of Guizhou University of Technology(Natural Science Edition.2004(2):12~14 (in Chinese) [2] Wang nian-qin.

Paper [8] suggested to diagnose inter-turn short circuit fault through the increase of generator journal vibration.
Finite element method is widely applied in synchronous machine electromagnetic field analysis, this method can take many factors into account, such as the actual motor operating conditions, the nonlinear of ferromagnetic materials, cogging and other factors, thus it is helpful to improve the generator electromagnetic parameters calculation accuracy.
Ignoring the ferromagnetic material anisotropy Assume that magnetic field distributes uniformly in the axial direction, so it is a two-dimensional static magnetic field.
BeiJing: Science Press,1992,p.405-484 [14] WU Yucai, LI Yonggang, LI Heming, WAN Shuting and JI Xuan.

Support Vector Linearly Inseparable Algorithm and its Optimizing Microwave Calcining Technology of Ammonium Uranyl Carbonate Qingzhi Du＊1,a 1Faculty of Information Engineering and Automation, Kunming University of Science and Technology, Kunming Yunnan, 650500, P.
Introduction Uranium is the material foundation for the development of nuclear industry; it has great strategic significance to protections of the national, the energy and the environmental securities.
In: Advance Materials Research, Vol. 382(2012) p. 281-288 [12] U.
JDCTA: International Journal of Digital Content Technology and its applications.

Nb-H Thin Films: On Phase Transformation Kinetics Vladimir Burlaka1, a, Kai Nörthemann1b and Astrid Pundt1,c * 1Institute of Material Physics, University of Göttingen, Friedrich-Hund-Platz 1, 37077 Göttingen, Germany avburlaka@ump.gwdg.de, bnoerthem@ump.gwdg.de, capundt@ump.gwdg.de Keywords: thin film, phase transformation, kinetics, metal-hydrogen systems.
High purity niobium (99.99%) was used as target material.
Pundt, International Journal of Hydrogen Energy 41 (2016) 2727
Fukai, The Metal-Hydrogen system, Springer Series in Material Science 21, Springer-Verlag, Berlin, Heidelberg, 1993, pp. 104-133