Search results

Acknowledgements This work was supported by the Ministry of Education and Science of Ukraine.
IOP Conference Series: Earth and Environmental Science, 61, 012007. https://doi.org/10.1088/1755-1315/61/1/012007 [12] Paggi, M., Ferro, G., & Braga, F. (2013).
Journal of Environmental Radioactivity, 78(2), 137-149. https://doi.org/10.1016/j.jenvrad.2004.04.004 [20] Hladkaia, E.V., Revva, V.N., & Riazancev, N.A. (2001).
Failure criteria for structurally heterogeneous materials.
Determining the impact of faukt amplitude using models of equivalent materials for the conditions of the Lvivsko-Volynskyi coal basin.

The maximum tensile strength (critical stress) of SS 304 material is ~ 515 MPa, [21] hence, the chamber can sustain ultra high vacuum.
This material is able to withstand high temperature and is vacuum compatible.
It is an interesting observation and has scope in fusion science and astrophysical research.
Acknowledgments We would like to thank Board of Research in Fusion Science & Technology (BRFST) for funding the project.
Chowdhuri: Asian Journal of Spectroscopy (2012), p. 231-238 [29] F.

Materials and Research Methods During this work cases of patients with injuries of capsular ligamentous apparatus in orthopedical unit after arthroscopy were examined.
Publications of scientists were used that had been published in foreign and Russian peer reviewed journals.
The search was conducted through the RSCI (Russian Science Citation Index) and scientific electronic library eLIBRARY.RU.
III congress of Russion arthroscopic community: materials.
Dissertation by candidate of medical sciences.

Energy Efficiency of Single-family Houses in Serbia and Montenegro: Strategy for Upgrading the Performance of Existing Stock Saja Kosanović1,a, Dragan Komatina2,b*, Radovan Nikčević 3,c, Vera Murgul4,d, Nikolay Vatin5,e 1Faculty of Technical Sciences, 38200, Kosovska Mitrovica, Serbia 2Faculty of Architecture, 81000 Podgorica, Montenegro 3Independent Energy Efficiency Expert, 11000 Belgrade, Serbia 4,5St.
Introduction Achieving and constantly enhancing the energy end-use efficiency accounts for generally recognized objective and one of the key research topics in contemporary technical sciences.
Energy efficiency in existing single-family residential stock, from all above noted, may be considered as a significant current challenge for the two subject countries, while at the same time, for comparison, in developed western countries the attention already moves to other aspects of ecological friendliness of buildings, such as building materials or embodied energy [5].
Ecological assessment of building materials in Serbia: Constraints and possibilities (2014) International Journal of Contemporary Architecture The New ARCH, Vol. 1 (1), pp. 51-58
Development and competitiveness improvement of the construction sector in Montenegro (2014) Applied Mechanics and Materials.

The fuel of forest biomass power generation belongs to forest biomass material, thus makes much lower emission of SO2 and NOX, and creates almost zero emission of CO.
Furthermore, forest biomass material belongs to renewable energy, consequently, its emission and absorption of CO2 constitutes nature carbon cycling.If we do not take the CO2 emission from the acquisition and transportation links into account, its energy utilization can achieve the zero emission of CO2 , even negative emission.
At present, fire coals is the major materials for thermal power generation in China.
There is tremendous diversity of resources advantages among different regions in the vast China, thus the choice of form of clean energy power generation mainly depends on the local resource endowment and has little relation with environmental cost (it will create low environmental cost in all forms of clean energy power generation).Compared with other forms of power generation (especially the nuclear energy power generation),the forest biomass power generation has the advantages of the low risks, relatively simple devices, technology easy to be popularized and spread, and relatively cheaper materials.
[10] Zhu Gao, Jing Feng, Faxin Yu, Xiaoling Wang, Yi Yan, Tengyun Liu: Journal of Anhui Agricultural Sciences Vol.4 (2011), p.54-57 In Chinese

Reaction Kinetics Investigation of Ni Ohmic Contacts on n-Type 4H-SiC Niannian Ge1,2,a, Caiping Wan1,2,b, Zhi Jin1,2,c and Hengyu Xu1,2,d* 1Institute of Microelectronics, Chinese Academy of Sciences, Beijing 100029, China 2University of Chinese Academy of Sciences, Beijing 100029, China ageniannian@ime.ac.cn, bwancaiping@ime.ac.cn, cjinzhi@ime.ac.cn, d*xuhengyu@ime.ac.cn Keywords: Ni/4H-SiC ohmic contacts, reaction kinetics, Raman spectra, active energy Abstract.
Kimoto, Material science and device physics in SiC technology for high-voltage power devices, Jpn.
Tanaka, In-situ high temperature X-ray diffraction study of Ni/SiC interface reactions, Journal of Materials Science 34 (1999) 235-239

Formation of Microstructure during Sub-Zero Treatments of Chromium and Chromium-Vanadium Ledeburitic Steels JURČI Peter Faculty of Material Sciences and Technology of the STU in Trnava, J.
Thus, the sub-zero treatment transformed from the "black-art" to the accepted topic of science.
In addition, Gavriljuk et al. [7] used powder metallurgy steel while conventional cast and wrought materials were used in other cited works.
Pendray, Cryoprocessing of Materials: A Review of Current Status, Mater.
Trnava: Faculty of Materials and Technology, Trnava, 2015

These luminescent materials may be applicable for scintillators.
These kind of luminescent materials can be used for white light-emitting diodes (LEDs).
Light: Science & Applications 2 (2013) e50- e50(8)
Schmidt, inorganic Luminescent Materials: 100 years of Research and application, J.
Metselaar, Luminescence Properties of Terbium, Cerium, or Europium doped α-Sialon Materials, J.

This happens due to different processes employed during production of gasoline and also due to characteristics of the petroleum used as raw material.
V., Consequence modeling using the fire dynamics simulator, Journal of Hazardous Materials 115 (2004) 149-154
W., Numerical Investigation of Neutral and Unstable Planetary Boundary Layers, Journal of Atmospheric Sciences 29 (1972) 91–115

As an alternative to the expensive high alloyed materials, a suitable coating system is developed for geothermal applications.
Materials and Methodology 2.1.
Materials The material used in the experiment is carbon steel, which was analyzed using spark optical emission spectrometer SPECTROLAB to determine the elemental composition as shown in Table 1.
Conover, Materials selection guidelines for geothermal energy utilization systems, NASA STI/Recon Technical Report N 81 (1981)
Dimper, Materials evaluation for geothermal applications in different geothermal waters, World Geothermal Congress 2015, 2015