Search results

Experimental Materials and Methods Donor and acceptor.
Scaffold material and reagent.
Ishikawa, Temperature-sensitive photoluminescence of CdSe quantum dot clusters., The Journal of Phys.
Ulijn, Enzyme responsive materials: design strategies and future developments, Biomater.
Clevers, Coexistence of quiescent and active adult stem cells in mammals., Science (New York, N.Y.). 327 (2010) 542–5

The characteristics of the overcritical propulsion system include a tuning wheel on the free end of the crankshaft and a turning wheel with relatively high inertia and shafts with relatively small diameters (requiring a shafting material with relatively high ultimate tensile strength).
Murawski, Axial vibrations of a propulsion system taking into account the couplings and the boundary conditions, Journal of Marine Science and Technology, Tokyo, 9(4) (2004) 171–181

Coalbed Methane (CBM) Project Enrichment Area and Economic Evaluation Jinshan Lia, Zhongxue Lib and Binghui Zuc The Ministry of Education Key Laboratory of High Efficiency Mining and Safety for Metal Mines, Department of Resources Engineering, University of Science and Technology Beijing, Beijing 100083, China alijinshan2009@126.com, bzxli@ustb.edu.cn, czbh6984179@163.com Keywords: Coalbed methane (CBM), enrichment, economic evaluation Abstract.
So, at first, the enrichment of coalbed methane is controlled by CBM generated material base.
Journal of China coal field geology, 1999, 11 (the first l) : 36 -38.

This soft magnetic material has some prominent advantages such as high magnetic induction and low specific iron losses.
Acknowledgement This project is supported by National Hi-tech Research and Development Program of China (863 Program, No.2008AA04Z116) and Hunan Province Natural Science Fund.
References [1] L.Lv,W.L.Xiong,H.Gao: Chinese Journal of Mechanical Engineering, Vol. 21(2008), pp.34-40.

But the test period of planned maintenance procedures are in accordance with the provisions of pre-trial, regardless of the actual state of power transformers, and has great coerciveness and blindness, which will cause the device "over-repair" and wasting of lots of human resources and material resources[1].
References [1] Sun Caixin, “Oil gas of electrical equipment online monitoring and fault diagnosis technology,” Beijing: science press, 2003
IEEE PES Power Systems Conference and Exposition,2004：1176-1182 [10] Li Junhao, Si Wenrong, Yang Jinggang, Yuan Peng, Li Yanmu, Li Yanming, “The research on characteristics of high frequency signal external propagation of power transformer partial discharge,” Journal of xi’an jiaotong university, Vol.42, No.6,PP. 718-722, 2008

Material of major parts of machine tool is HT250 which is high-strength cast iron and it has elasticity modulus 1.5×105Mpa, Poisson ratio 0.26 and density 7.8×10-9 t /mm3 [2].
Journal of Fuzhou University( Natural Science),2003(2):69-72

For consideration of reducing material, this study preliminarily concludes that the radius of the semi-circle wind deflector (r) should be 4.5m.
UK: Multi-Science Pub, (2006)
Journal of Wind Engineering and Industrial Aerodynamics, 74-76 (1998) 1-24

Comparative study on design of exposed penstock laid on ground using Chinese and American specifications Lei Hu 1, a, Hegao Wu 1, b, Changzheng SHi 1, c, Yinghan Xie 2, d 1State Key Laboratory of Water Resources and Hydropower Engineering Science, Wuhan University, Wuhan 430072, China 2Changjiang institute of survey, planning, designing and research, Wuhan 430010, China aleih1209@gmail.com, bwbf1988@vip.sina.com, cscz4@163.com, dyhxie01@hotmail.com Keywords: hydropower station, exposed penstock laid on ground, DL/T 5141-2001, ASCE No.79, allowable stress, load combination.
It is a coefficient synthesizing partial factors for loads and material properties.
Journal of Hydraulic Engineering, 2012, 43(8): 957-966.

Behavior of the leaning tower of Pisa: insights on seismic input and soil-structure interaction Raffaello Bartelletti1,a, Gabriele Fiorentino2,b*, Giuseppe Lanzo3,c, Davide Lavorato 2,b, Giuseppe Carlo Marano4,e, Giorgio Monti3,f, Camillo Nuti2,5,g, Giuseppe Quaranta3,g, Fabio Sabetta6,i and Nunziante Sgueglia1,j 1University of Pisa, Via Diotisalvi 2, 56126 Pisa, Italy 2Dept. of Architecture, Roma Tre University, Largo Giovanni Battista Marzi, 10, 00153 Rome, Italy 3Dept. of Structural and Geotechnical Engineering, Sapienza University of Rome, Via Gramsci 53, 00197 Rome, Italy 4 Dept. of Science of Civil Engineering and Architecture, Technical University of Bari, Via Orabona 4, 70125 Bari, Italy 5Visiting Professor at Fuzhou University, College of Civil Engineering Fuzhou, Fujian 350108, China 6 Department of Civil Protection, Via Vitorchiano 4, 00189 Rome, Italy ar.bartelletti@ing.unipi.it, b gabriele.fiorentino@uniroma3.it, cgiuseppe.lanzo@uniroma1.it, ddavide.lavorato@
They are homogenized by assuming the whole sections made of marble of San Giuliano (the material of the walls of the Tower), which has a modulus of elasticity E=80,000 MPa; · at the base of the model were assigned 3 translational springs and 3 rotational springs, for which the impedances reported in Table 2 are considered.
Viggiani, Leaning Tower of Pisa: Behaviour after Stabilization Operations, International Journal of Geoengineering.

Definition of Boundary Conditions and Dynamic Analysis of Rocket Sled and Turntable Zhang Jianhua1, a, Jiang Shoushan2,b 1 Institute of Science, Chang’An University Xi'an, China 2 Institute of Mechanical Engineering,Northwestern Polytechnical University,Xi’an,China azhangjianh@chd.edu.cn, bjiangshoushan@yahoo.com.cn Keywords: Rocket Sled；Multibody System Dynamics Analysis(MDA)； Finite Element Analysis (FEA)；Boundary Condition； Simulation; Rail Irregularity Abstract.
ADAMS MD A ANSYS F E A Inducting the FBM to ANSYS by the special interface Defining elements, material properties, meshing Outputing .mnf files by Macro command Doing statics, transient dynamics spectral analysis Outing the results of FEA Inducting the model created by Pro/E to ADAMS2005 Defining rigid body’s kinematic pair and constraits Inputting modal neutral files Creating RFCM, adding boundary conditions Outputting the results of MDA Creating Assembly ly Model in Pro/E Fig.1 Procedure of the Joint Simulation of Pro/E,ADAMS,ANSYS Creating Rigid-Flexible Coupling Model The Necessary Assumptions to Simplify the Model.
[6] Choi K K．Design sensitivity analysis of structure-inducednoise and vibration[J]．Journal of Viberation and Acoustics，1997，119:173-179