Impact of an Excessive Wear of Bearing on the Mechatronic Devices

Abstract:

The article studies, based on the evaluation of the experimental research, effectiveness of independent and combined interaction of selected methods when diagnosing bearing of the mechatronic device in course of 6 months. During this time the general overhaul of the device was carried out, where the measurements, analyses and evaluations were focused on run-in and a shorter after run-in period of the bearing.

• Periodical: Applied Mechanics and Materials (Volume 460)
• Pages: 99-106
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.460.99
• Online since: November 2013
• Authors: Peter Čačko*, Tibor Krenický, Jozef Dobránsky
• Keywords: Diagnostics, Experiment, Mechatronics, Monitoring

References

[1] S. Fabian, P. Čačko, Experimental measurement and examination of independent and combined interaction of vibrodiagnostic and tribotechnical methods, in: Applied Mechanics and Materials: Operation and Diagnostics of Machines and Production Systems Operational States. 308 (2013) 51-56.

DOI: 10.4028/www.scientific.net/amm.308.51

[2] A. Panda, I. Pandová, Production inner ring of tapered roller bearings. Scientific bulletin, serie C, Volume XXIII: Mechanics, Tribology, Machine Manufacturing Technology. North university of Baia Mare (2009) 149 –152.

[3] A. Panda, Jurko, J., M. Džupon, I. Pandová, Optimalization of Heat Treatment Bearings Rings with Goal to Eliminate Deformation of Material. Chemické listy, Material in Engineering Practice 2011, Vol. 105, Special issue, Association of Czech Chemical Societes, Praha, HF TU Košice, Herľany (2011) 459-461.

[4] K. Monková, P. Monka, Surface Roughness Characteristics and Structure of Steel C45 after Wc-Co Coating and Laser Treatment, Advanced Materials Research 622-623 (2012) 370-374.

DOI: 10.4028/www.scientific.net/amr.622-623.370

[5] S. Šoltésová, P. Baron, The Operation Monitoring Condition of the Production Machinery and Facilities Using the Tools of Technical Diagnostics, Applied Mechanics and Materials 308 (2013) 105-109.

DOI: 10.4028/www.scientific.net/amm.308.105

[6] K. Monková, P. Monka, Group Technology Utilization inside New Software Application, Applied Mechanics and Materials 229-231 (2012) 2765-2769.

DOI: 10.4028/www.scientific.net/amm.229-231.2765

[7] S. Šoltésová, P. Baron, Methods assigned for monitoring the operating fault state of production equipments, Journal CA Systems in Production Planning 14 (2013) 31-33.

DOI: 10.4028/www.scientific.net/amm.404.473

[8] J. Semjon, P. Demeč, J. Svetlík, Virtual model of tool path for milling machine at classical design base, Applied Mechanics and Materials 282 (2013) 235-241.

DOI: 10.4028/www.scientific.net/amm.282.235

[9] T. Stejskal, J. Kováč, Š. Valenčík, Mechanism of randomness in vibration signals of machinery, Applied Mechanics and Materials 282 (2013) 257-262.

DOI: 10.4028/www.scientific.net/amm.282.257

[10] J. Svetlík, P. Demeč, Virtual model of tool path for milling machine at classical design base, Applied Mechanics and Materials 282 (2013) 235-241.

DOI: 10.4028/www.scientific.net/amm.282.235

[11] J. Paško, Š. Gašpár, Experimental monitoring of HB hardness and ultimate tensile strength UTS of pressure of Al-Si castings depending on the increase pressure changes, Advanced Materials Research 711 (2013) 272-275.

DOI: 10.4028/www.scientific.net/amr.711.272

[12] I. Vojtko, Vibration of Worm Gear Boxes, Applied Mechanics and Materials 308 (2013) 45-49.

DOI: 10.4028/www.scientific.net/amm.308.45

[13] J. Novák–Marcinčin, et al., Visual Reconstruction and Optimization of Real Workplace on the Base of Spatial Digitisation, Applied Mechanics and Materials 308 (2013) 175-178.

DOI: 10.4028/www.scientific.net/amm.308.175

[14] J. Duplák, M. Hatala, P. Michalik, Durability analysis for selected cutting tools in machining process of steel 16mov6-3, Applied Mechanics and Materials 308 (2013) 133-139.

DOI: 10.4028/www.scientific.net/amm.308.133

[15] E. Ragan et al., Materials on Dies for Pressure Die Casting, Metalurgija 51 (2012) 117-120.