Investigating Foamed Bitumen Viscosity

Abstract:

Foamed bitumen is a binder of cold mix road recycling materials. It is necessary to understand the best foamed bitumen properties prior to mixing with aggregate materials. Viscosity is one of the important properties, which facilitate the foam to distribute across the aggregate phase in the mixing process, and form a well coated asphalt mix. Unfortunately, the understanding of foamed bitumen viscosity and its contribution in the development of mixture performance is still poorly understood. This paper discusses foamed bitumen viscosity which was explored based on theoretical studies and a series of laboratory investigation. Foamed bitumen was produced using bitumen Pen 70/100 at temperature of 180°C. The research method was developed in three activities, i.e. (1) the previous studies on the foamed bitumen rheology, (2) investigating flow behavior of foamed bitumen, and (3) estimating foamed bitumen viscosity using Kraynik equation.The research results can be summarized in the following three points. First, foamed bitumen consists of gas content and liquid bitumen, in which the value of foam viscosity increases with the gas content. Second, foam flow can be used to indicate the apparent foam viscosity. Foamed bitumen with a higher foaming water content (FWC) tends to have a decreased flow rate and hence higher apparent viscosity. Third, foamed bitumen viscosity estimated using Kraynik equation is affected by gas content and liquid bitumen viscosity. It was found that an ER_m of around 35 (or at FWC of 6%) is the critical area of foam viscosity.

• Periodical: Applied Mechanics and Materials (Volume 660)
• Pages: 254-258
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.660.254
• Online since: October 2014
• Authors: Sunarjono Sri*, Hartadi Sutanto Muslich
• Keywords: Cold Mix Road Recycling Materials, Flow, Foamed Bitumen, Viscosity

References

[1] S. Sunarjono, The Influence of Foamed Bitumen Characteristics on Cold Mix Asphalt Properties, PhD Thesis, University of Nottingham, Nottingham, (2008).

[2] L.L. Schramm, Foams: Fundamentals and Applications in the Petroleum Industry. Advances in Chemistry series 242, American Chemical Society, Washington DC, (1994).

[3] C.J.W. Breward, The Mathematics of Foam, PhD Thesis, St. Anne's College, University of Oxford, (1999).

[4] S. Sunarjono, Foamed Bitumen Structure, The 16th Internasional symposium of the Indonesian inter university transport studies forum, Universitas Muhammadiyah Surakarta, Surakarta, (2013).

[5] G. R. Assar, R. W. Burley, Hydrodynamics of foam flow in pipes, capillary tubes, and porous media. In Encyclopedia of Fluid Mechanics, edited by N.P. Cheremisinoff, Vol. 3, pp.26-42. (1986).

[6] D. Weaire, S. Hutzler, The Physics of Foams, Oxford University Press, Great Clarendon Street, Oxford OX2 6DP, (1999).

[7] J.P. Heller, M.S. Kuntamukkula, Critical review of the foam rheology literature, Ind. Eng. Chem. Res. Vol. 26, No. 2, 1987, pp.318-325, © 1987 American Chemical Society, (1987).

DOI: 10.1021/ie00062a023

[8] K.J. Jenkins, Characterisation of Foamed Bitumen, Chapter 3, Mix Design Considerations for Cold and Half-warm Bituminous Mixes with Emphasis on Foamed Bitumen, PhD Dissertation, University of Stellenbosch, South Africa, (2000).

[9] J. Read, D. Whiteoak, The Shell Bitumen Handbook, fifth edition, ISBN: 0 7277 3220 X, Shell UK Oil Products Limited, (2003).

[10] A.M. Kraynik, Foam Flows, Annual reviews Fluid Mechanics 1988. 20: 325-57. Fluid and Thermal Sciences Department, Sandia National Laboratories, Albuquerque, New Mexico 87185, (1988).

DOI: 10.1146/annurev.fl.20.010188.001545