A Novel Alignment Technique in Wafer-Level Packaging of MEMS Components

Abstract:

In recent years, assembling and packaging methods of Micro Electro Mechanical System (MEMS) components have been profoundly studied. The focus of this paper is presenting a novel alignment technique in wafer-level packaging. In conventional wafer-level strategies, either an Alignment Template (AT) must have special receptor sites according to the microchip geometry and its material, or the microcomponents should be additionally featured by circular and cross pegs for shape recognition stage. In this article, we have developed electrothermal microclamps (ETMCs) to hold and locate six microchips of 360×360×20 micrometers in a microfixturing cell. This is to provide accurate preliminary positioning for final flip-chip bonding process of wafer-level packaging on a main assembly board (MAB). The new approach enjoys the advantages of omitting special AT with receptor sites and using identical ETMCs for diverse assembly configurations. Being applicable for different types of microcomponent materials, it does necessitate no surface treatment on microcomponents such as Semidry uniquely orienting self-organizing parallel assembly (Semi-DUO-SPASS) technique. Comparing nickel and polysilicon as fabrication materials, corresponding values of input voltage to reach 3 micrometers displacement of the ETMC arm are estimated via finite element analysis to ascertain positioning and holding of microchips. Nickel showed to be a better choice for fabrication due to requiring lower input voltage and lower maximum resulting temperature. The simulation results are verified with published experimental measurements.

• Periodical: Advanced Materials Research (Volumes 403-408)
• Pages: 4564-4571
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.403-408.4564
• Online since: November 2011
• Authors: M. Hamedi, M. Vismeh, P. Salimi
• Keywords: Electrothermal Actuation, Microclamp, Micro-Electromechanical System (MEMS), Micro-Fixture, Wafer-Level Packaging

References

[1] J. Fang and K.F. Bohringer, Wafer-level packaging based on uniquely orienting self assembly (the DUO-SPASS processes), J. Microelectromechanical systems, 2006, vol. 15, p.531–540.

DOI: 10.1109/jmems.2006.876790

[2] J. Fang, Self-assembly techniques for massively parallel packaging of MEMS devices, PhD thesis, University of Wshington, (2006).

[3] T.G. kollie, Measurment of the thermal-expansion coefficient of nickel from 300 to 1000 K and determination of the constant near the curie temperature, J. PHYSICAL REVIEW B, 1977, vol. 16, No. 11, pp.4872-4882.

DOI: 10.1103/physrevb.16.4872

[4] P.H.D. Godoy and E.C.N. silva, Aspects of Fabrication and Characterization of electro-thermal micro actuators, J. ABCM symposium series in mechatronics, 2006, vol. 2, pp.517-524.

[5] R.D. Lide and V.H. Kehiaian, CRC Handbook of thermophysical and thermomechanical data, Ann Arbor, MI, (1994).

[6] Y. Okada and Y. Tokumaru, Precise determination of lattice parameter and thermal expansion coefficient of silicon between 300 and 1500 K, J. Appl. Phys, 1984, vol. 56, pp.314-320.

DOI: 10.1063/1.333965

[7] N.D. Mankame, K.G. Ananthasuresh, Comprehensive thermal modeling and characterization of an electro-thermal-compliant microactuator, J. Micromech. Microeng., 2001, vol. 11, pp.452-462.

DOI: 10.1088/0960-1317/11/5/303

[8] Incropera, DeWitt, Bergman and Lavine, Fundamentals of heat and mass transfer, 6th Ed, John Wiley & Sons, (2007).

[9] J. K. Luo, Y. Q. Fu, J. A. Williams, and W. I. Milne, Thermal Degradation of Electroplated Nickel Thermal Microactuators, , J. MICROELECTROMECHANICAL SYSTEMS, 2009. Vol. 18, No. 6, pp.1279-1287.

DOI: 10.1109/jmems.2009.2034394

[10] S.E. Kolesar, T. Htun, B. Least, J. Tippey and J. Michalik, Optimization of the geometry of MEMS electrothermal actuator to maximize in- plane tip deflection, Mater. Res. Soc. Sympo. Proc, 2008, vol. 1052, pp.105-110.

DOI: 10.1557/proc-1052-dd03-12

[11] J.K. Luo et al, Development of all metal electro-thermal actuators and its applications, J. Microlith. Microfab. Microsyst., vol. 4, no. 2, pp.023012-1, (2005).

[12] W. Wang, L. Svetlana Tatic, W. Brown, J. Iceman, S. Hyun and R. Vinci, Precision in-package positioning with a thermal inchworm, J. Sensors and Actuators, 2008, vol. A142, pp.316-321.

DOI: 10.1016/j.sna.2007.04.049

[13] J.S. Lee, D. Sang, W. Park, A.K. Nallani, G.S. Lee and J.B. Lee, Sub-micron metallic electothermal actuators, , J. Micromech. Microeng, 2005, vol. 15, pp.322-327.

DOI: 10.1088/0960-1317/15/2/011