Effect of Different Aluminium Surface Treatments on Ice Adhesion Strength

Abstract:

Excessive ice accumulation on power network equipment can affect their integrity and cause damage with serious socioeconomic consequences. To mitigate that, de-icing techniques (mechanical or thermal) have been developed, but these techniques are often limited in their application and are generally expensive and time consuming. Recently, companies and research groups have focused on the development and application of icephobic coatings such as superhydrophobic materials intended to drastically reduce ice adhesion force on exposed equipments. The aim of this paper is the examine the influence of aluminium surface treatments on ice adhesion. Preparation of new and various aluminium surface treatments as well as the need to improve the knowledge of the mechanisms involved in ice adhesion are part of this research. Depending of the type of materials, surface roughness can either promote the formation of air pockets within pores or between coating surface asperities (low adhesion strength), or it can create ice mechanical anchoring if water partially or totally penetrates the porosity. Aluminium anodization using phosphoric acid was studied. Surface morphology was evaluated using scanning electron microscopy and measurements of ice adhesion strength were performed using a centrifuge technique. Based on these results, several surface treatments of aluminium have been considered including aluminium anodizing with partial Al₂O₃ etching followed by different sealing steps using hydrophobic polymer compounds such as polytetrafluoroethylene.

• Periodical: Advanced Materials Research (Volume 409)
• Pages: 788-792
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.409.788
• Online since: November 2011
• Authors: Z. Ghalmi, R. Menini, M. Farzaneh
• Keywords: Aluminum (Al), Anodization, Hydrophobicity, Icephobicity, PTFE

References

[1] M. Farzaneh (Chair), Systems for prediction and monitoring of ice shedding, anti-icing and de-icing for overhead lines, CIGRÉ WG B2. 29, CIGRE Publications, Technical Brochure #438, (2010) 100 p.

DOI: 10.1007/978-3-030-87455-1_3

[2] A. Safaee, D.K. Sarkar and M. Farzaneh, Superhydrophobic Properties of Silver-Coated Films on Copper Surface by Galvanic Exchange Reaction, Applied Surface Science. 254 (2008) 2493-2498.

DOI: 10.1016/j.apsusc.2007.09.073

[3] D. Sarkar, M. Farzaneh and R. Paynter, Superhydrophobic properties of ultrahin rf-sputtered Teflon films coated etched aluminium surfaces, Materials Letters. 62 (2008) 1226-1229.

DOI: 10.1016/j.matlet.2007.08.051

[4] R. Menini, M. Farzaneh, Elaboration of Al2O3/ PTFE icephobic coating for protecting aluminum surfaces, Surface and Coating Technology. 203 (2009) 1941-(1946).

DOI: 10.1016/j.surfcoat.2009.01.030

[5] S.A. Kulinich, M. Farzaneh, Ice adhesion on super-hydrophobic surfaces, Applied surface science. 255 (2009) 8153-8157.

DOI: 10.1016/j.apsusc.2009.05.033

[6] N. Saleema, M. Farzaneh, R.W. Paynter and D.K. Sarkar, Prevention of ice accretion on aluminium surfaces by enhancing their hydrophobic properties. Journal of adhesion science and technology, 25 (2011) 27-40.

DOI: 10.1163/016942410x508064

[7] R. Menini, Z. Ghalmi and M. Farzaneh, Highly resistant icephobic coatings on aluminum alloys. Cold Regions Science and Technology, 65 (2011) 65-69.

DOI: 10.1016/j.coldregions.2010.03.004

[8] R. Jafari, R. Menini and M. Farzaneh, Superhyrophobic surfaces prepared b RF-sputtered poytetrafluoroethyene coating, Journal of applied surface science, 257(2010) 1540-1543.

DOI: 10.1016/j.apsusc.2010.08.092

[9] Z. Ghalmi, R. Menini and M. Farzaneh, Experimental study of the influence of the type of material, roughness and temperature on ice adhesion, IWAIS 2011, Chongqing, China, (2011).

[10] J. Brandrup, E.H. Immergut, E.A. Grulke, in Polymer Handbook, J. Wiley (ed. ), New York, (1999).

[11] L. Yin, Q. Xia, J. Xue, S. Yang, Q. Wang and Q. Chen, In situ investigation of ice formation on surfaces with representative wettability, Applied Surface Science, 256 (2010) 6764–6769.

DOI: 10.1016/j.apsusc.2010.04.086