Simulation on Slinging and Reshipment System in Mine

Jun Xia Li; Zhi Qiang Jin; Rong Quan Wang; Zi Ming Kou

doi:10.4028/www.scientific.net/AMR.619.264

Paper Titles

Study on Reducing PM Emission and Regenerating DPF of NTP System in Diesel Engines
p.244

Study of the Wheel of Abrasive Belt Based on Forming Polishing Technology
p.249

Floor Destruction Characteristic Study of Confined Water Effected by Mining Conditions
p.253

Fault Diagnostic of Electro-Hydraulic Servo Valve
p.259

Simulation on Slinging and Reshipment System in Mine
p.264

Study of a New High Frequency Moving Coil Linear Force Motor for Electro Hydraulic Servo Valve
p.270

The Weight Reduction Optimization of Jaw Crusher about Moving Jaw Based on Parametric Finite Element Analysis
p.275

Structure Optimization on Sensitivity Analysis for Ultra-Supercritical Bypass Valve
p.282

Review of Coal Tar Preparation and Processing Technology
p.286

HomeAdvanced Materials ResearchAdvanced Materials Research Vol. 619Simulation on Slinging and Reshipment System in...

Simulation on Slinging and Reshipment System in Mine

Abstract:

Aiming at the problenm of transportation to underground, and slinging, reshipment, assembly in underworkings for mining lage equipment , a set of slinging and reshipment system in the underground is developed. This system is a steel-frame structure consisted of multi-unit bridged structure junction,in which the double T-iron is taken as main load-bearing beam,and U-steel unit welded by back-to-back method is as a slanted prop triangle secondary beam.This system adoptes the three-dimensional modeling software Solidworks2007, and its COSMOS/Works modules, for the three-dimensional modeling and finite element analysis to this system. Through the finite element analysis, verified the correctness of the component design.

You might also be interested in these eBooks

Hydraulic Equipment and Support Systems for Mining

View Preview

Info:

Periodical:

Advanced Materials Research (Volume 619)

Pages:

264-269

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.619.264

Citation:

Cite this paper

Online since:

December 2012

Authors:

Jun Xia Li, Zhi Qiang Jin, Rong Quan Wang, Zi Ming Kou

Keywords:

Dynamic Simulation, Finite Element Analysis (FEA), Hydraulic System, Reshipment, Slinging

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] Chang Kai. Selection discusses on Coal mine hydraulic support van[J]. Coal Mine Machinery，2010(6), 31(6): 72-74.

Google Scholar

[2] Zhang Xin. The design of four-bar linkage of large inclined angle hydraulic support [R]. 2009 International Conference on Engineering Computation, ICEC 2009, pp.167-170.

DOI: 10.1109/icec.2009.68

Google Scholar

[3] Zhang Lianbao, Wu Zhizhen. The application technology research of integrated mining face pulling face lifting bracket and complex geological conditions[J]. Mining Machinery，2008, 36(19): 29-31.

Google Scholar

[4] Mao Yuhu，Liu Renquan，The design and application of hoisting locks[J]，Coal Technology，2006, 25（9）：19.

Google Scholar

[5] The fourth design institute of the third machinery industry ministry, The design and calculation of electric beam crane [M]. XI'an：The fourth design institute of the third machinery industry ministry，1976：58-89.

Google Scholar

[6] Wang Jun. Solidworks2007 Introduction and improve[M]. Beijing Science Press，2008：69-98.

Google Scholar

[7] Wang Rongquan，Kou Ziming，Li Xindong. The design and application of Underground tunnels hoisting reproduced system[J]. Coal Mine Machinery，2011(4).

Google Scholar

[8] Cui Zhigang，The development of mine large hydraulic support assembly platform [J]，Coal mining，2008, 13（6）：76.

Google Scholar