Influence of Chamfer Size on the Two-Side Direction Burr Formed in Grinding-Hardening Machine

Ju Dong Liu; Wei Yuan; Jin Kui Xiong; Zhi Long Xu

doi:10.4028/www.scientific.net/AMR.645.392

Paper Titles

Mechanical Analysis of Vibrating-Beam Resonantor Accelerometer
p.373

Empirical Formula for Stress Intensity Factor of Crack Initiated from an Interface Edge
p.377

The Integrated Design of a New Intelligent Fuze Safety System Based on Piezoelectric Actuator
p.381

A Fast Approach for Reduction of Torque Ripple on BLDC Motor
p.387

Influence of Chamfer Size on the Two-Side Direction Burr Formed in Grinding-Hardening Machine
p.392

Appropriate Boundary Conditions for Nonlocal Elastic Beams
p.396

Design of Bypass-Throttle Hydraulic Cylinder Speed Control System Base on High-Speed On-Off Valve
p.405

Influence after Distributed Generation Access to the Distribution Network and its Reactive Power Control Strategy
p.409

Study of the Parallel Hybrid Electric Vehicle Drive Train Fuzzy Logic Control Strategy
p.413

HomeAdvanced Materials ResearchAdvanced Materials Research Vol. 645Influence of Chamfer Size on the Two-Side...

Influence of Chamfer Size on the Two-Side Direction Burr Formed in Grinding-Hardening Machine

Abstract:

Based on the orthogonal experiment, this paper studied the influences of chamfer size on the two-side direction burr in grinding-hardening machine. The results show that: chamfer height size affected the two-side direction burr’s size significantly and the influence of chamfer degree α is general. On this experimental condition, it should adopted grinding parameter ap＝0.2mm,vw＝0.2m/min, the chamfer height h=1.0mm and chamfer degree α=20 o to reduce the two-side direction burr’s size effectively and decrease the workload of removing burr.

You might also be interested in these eBooks

Intelligent System, Applied Materials and Control Technology

View Preview

Info:

Periodical:

Advanced Materials Research (Volume 645)

Pages:

392-395

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.645.392

Citation:

Cite this paper

Online since:

January 2013

Authors:

Ju Dong Liu, Wei Yuan, Jin Kui Xiong, Zhi Long Xu

Keywords:

Chamfer Size, Grinding, Surface Hardening, Two-Direction Burr

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] E. Brinksmeier, T. Brockhoff: HTM Vol. 49(1994), P. 327-330.

Google Scholar

[2] E. Brinksmeier, T. Brockhoff: Annals of the CIRP Vol. 45(1996), P. 283-286.

Google Scholar

[3] T. Brockhoff : Annals of the CIRP Vol. 48 (1) (1999), P. 255-260.

Google Scholar

[4] I. Zarudi, L. C. Zhang: Journal of Materials Science Vol. 37 (2002),P. 3935-3943.

Google Scholar

[5] J. D. Liu, G. C. Wang, Q. F. Li, et al: Materials Science Forum Vol. 532-533 (2006), P. 584-587.

Google Scholar

[6] G. C. Wang, J. D. Liu, H. J. Pei, et al: Key Engineering Materials Vol. 304-305(2006),P. 588-592.

Google Scholar

[7] T. Nguyen, L. C. Zhang: Advanced Materials Research Vol. 76-78 (2009), pp.3-8.

Google Scholar

[8] T. Nguyen, L. C. Zhang: Key Engineering Materials Vol. 443 (2010), pp.388-393.

Google Scholar

[9] J. D. Liu, J. Z. Zhuang: Advanced Materials Research Vol. 102-104(2010), pp.733-737.

Google Scholar

[10] J. D. Liu, J. Z. Zhuang and S. W. Huang: Key Engineering Materials Vol. 455(2011), pp.580-584.

Google Scholar

[11] J. K. Xiong, J. D. Liu, W. Yuan: Advanced Materials Research Vol. 505(2012), pp.26-30.

Google Scholar