Orthogonal Experimental Study on the Grinding-Hardened Layer’s Depth and its Uniformity of 45 Steel

Wei Yuan; Ju Dong Liu; Zhi Long Xu

doi:10.4028/www.scientific.net/AMR.668.898

Paper Titles

Effects of Electrolyte Parameters on Properties of Ceramic Coatings Formed on Aluminum Alloy 7075 by Plasma Electrolytic Oxidation
p.875

Effects of Surface Oxide Coating on Corrosion Behavior of Ti-1023/LY12 Galvanic Couple
p.880

Investigation of Microstructure and Properties of an Al-Zn-Mg-Cu Alloy
p.885

Influence of Welding Sequence on Residual Stress and Distortion in Rectangular Welding of 6061 Aluminum Alloy
p.890

Orthogonal Experimental Study on the Grinding-Hardened Layer’s Depth and its Uniformity of 45 Steel
p.898

Mechanism Analysis and Dairy Filtration Experimental Research on Porous 1Cr18Ni9 Stainless Steel Components
p.902

Quench Sensitivity and Quench-Induced Precipitation in High Strength 7xxx Series Aluminum Alloys
p.907

The Determination of the Heat Release Rate on Cotton Smoldering Fire and Polyurethane Fire
p.915

Dynamic Mechanical Properties of Trimethylborate (TMB) Modified Poplar Wood by Sol-Gel Process
p.920

HomeAdvanced Materials ResearchAdvanced Materials Research Vol. 668Orthogonal Experimental Study on the...

Orthogonal Experimental Study on the Grinding-Hardened Layer’s Depth and its Uniformity of 45 Steel

Abstract:

Based on the orthogonal experiment of grinding-hardening machine, this paper studied the influence of depth of cut ap, table speed vw and grinding method gm on the grinding-hardened layer’s depth and its uniformity of 45 steel. The results show that, depth of cut ap is the significant factor affected the average value of grinding-hardened layer’s depth, but the influence of grinding conditions on the uniformity are very limited. In actual application, it should adopt ap=0.6mm, vw=0.4m/min and up-down grinding method to enhance the quality of grinding-hardened layer.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Advanced Materials Research (Volume 668)

Pages:

898-901

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.668.898

Citation:

Cite this paper

Online since:

March 2013

Authors:

Wei Yuan, Ju Dong Liu, Zhi Long Xu

Keywords:

Depth, Grinding-Hardening, Orthogonal Experiment, Uniformity

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] E. Brinksmeier, T. Brockhoff: HTM Vol. 49(1994), P. 327-330.

Google Scholar

[2] E. Brinksmeier, T. Brockhoff: Annals of the CIRP Vol. 45(1996), P. 283-286.

Google Scholar

[3] T. Brockhoff : Annals of the CIRP Vol. 48 (1) (1999), P. 255-260.

Google Scholar

[4] I. Zarudi, L. C. Zhang: Journal of Materials Science Vol. 37 (2002), P. 3935-3943.

Google Scholar

[5] J. D. Liu, G. C. Wang, Q. F. Li, et al: Materials Science Forum Vol. 532-533 (2006), P. 584-587.

Google Scholar

[6] G. C. Wang, J. D. Liu, H. J. Pei, et al: Key Engineering Materials Vol. 304-305(2006),P. 588-592.

Google Scholar

[7] T. Nguyen, Zarudi I, L. C. Zhang: International Journal of Machine Tools and Manufacture Vol. 47(1) (2007) pp.97-106.

Google Scholar

[8] J. D. Liu, G. C. Wang, D.P. Hou: Journal of Basic Ssience and Engineering Vol. 16(4)(2008) pp.574-579 (In Chinese).

Google Scholar

[9] T. Nguyen, L. C. Zhang: Advanced Materials Research Vol. 76-78 (2009), pp.3-8.

Google Scholar

[10] T. Nguyen, L. C. Zhang: Key Engineering Materials Vol. 443 (2010), pp.388-393.

Google Scholar

[11] J. D. Liu, J. Z. Zhuang: Advanced Materials Research Vol. 102-104(2010), pp.733-737.

Google Scholar

[12] T. Nguyen, L. C. Zhang D. Sun: Advanced Materials Research Vol. 325(2011), pp.35-41.

Google Scholar

[13] J. D. Liu, J. Z. Zhuang and S. W. Huang: Key Engineering Materials Vol. 455(2011), pp.580-584.

Google Scholar

[14] T. Nguyen, L. C. Zhang: Materials Science Forum Vol. 697-698(2012), pp.13-18.

Google Scholar

[15] J. K. Xiong, J. D. Liu, W. Yuan: Advanced Materials Research Vol. 505(2012), pp.26-30.

Google Scholar