Fatigue Behaviour of AZ91 Magnesium Alloy in as-Cast and Severe Plastic Deformed Conditions

Abstract:

Fatigue strength, crack initiation and microstructure were experimentally investigated in an as-cast AZ91 alloy and in ultrafine-grained (UFG) AZ91 alloy processed by equal channel angular pressing (ECAP). The microstructure after ECAP is bimodal, consisting of fine-grained regions and clusters of larger grains with lower density of intermetallic particles. It has been found that the ECAP substantially increases the tensile strength (factor of two), improves ductility (factor of five) and improves the fatigue strength in low-cycle fatigue region. The improvement of the endurance limit based on 10⁷ cycles is weak. The cyclic slip bands, as sites of the fatigue crack initiation on material surface, were investigated. Focussed ion beam technique (FIB) was applied to reveal the surface relief and the microstructure in the vicinity of early fatigue cracks. No grain coarsening was observed in the close vicinity of the initiated cracks. Fatigue cracks in ultrafine-grained structure develop both in the regions of larger grains and also in the fine grained areas. Two types of crack initiation were observed.

• Periodical: Advanced Materials Research (Volumes 891-892)
• Pages: 397-402
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.891-892.397
• Online since: March 2014
• Authors: Ludvík Kunz, Stanislava Fintová
• Keywords: AZ91, Cyclic Plastic Deformation, ECAP, Fatigue Crack Initiation, Mechanical Property, Microstructure

References

[1] H. Altwicker et al., Magnesium und seine Legierungen, J. Springer Verlag, Berlin, (1939).

[2] B.L. Mordike, T. Ebert, Magnesium. Properties - applications - potential, Mat. Sci. Eng. A302 (2001) 37-45.

[3] Ch.S. Chung, D.K. Chun, H.K. Kim, Fatigue properties of fine grained magnesium alloys after severe plastic deformation, J. of Mech. Sci. and Technol. 7 (2005) 1441-1448.

DOI: 10.1007/bf03023903

[4] H.K. Kim, Y.I. Lee, Ch. S. Chung, Fatigue properties of fine-grained magnesium alloy produced by equal channel angular pressing, Scripta Mater. 52 (2005) 473-477.

DOI: 10.1016/j.scriptamat.2004.11.007

[5] Z. Zúberová, L. Kunz, T.T. Lamark, Y. Estrin, M. Janeček, Fatigue and tensile behavior of cast, hot-rolled, and severely plastically deformed AZ31 magnesium alloy, Met. Mat. Trans. 38A (2007) 1934-(1940).

DOI: 10.1007/s11661-007-9109-6

[6] W.J. Kim, C.V. An, Y.S. Kim, S.I. Hong, Mechanical properties and microstructure of an AZ61 Mg alloy produced by equal channel angular pressing, Scripta Mater. 42 (2002) 39-44.

DOI: 10.1016/s1359-6462(02)00094-5

[7] W.J. Kim, S.I. Hong, Y.S. Kim, S.H. Min, H.T. Jeoung, J.D. Lee, Texture development and its effect on mechanical properties of an AZ61 Mg alloy fabricated by equal channel angular pressing, Acta Mater. 51 (2003) 3293-3307.

DOI: 10.1016/s1359-6454(03)00161-7

[8] L. Jin, D. Lin, D. Mao, X. Zeng, W. Ding, Mechanical properties and mcirostrcuture of AZ31 Mg alloy processed by two-step equal channel angular extrusion, Mater. Letters 59 (2005) 2267-2270.

DOI: 10.1016/j.matlet.2004.09.061

[9] L. Wu, G.M. Stoica, H.H. Liao, S.R. Agnew, E.A. Payzant, G. Wang, D.E. Fielden, L. Chen, P. Liaw, Fatigue property enhancement of magnesium alloy, AZ31B, through equal channel angular pressing, Met. Mat. Trans. 38A (2007) 2283-2289.

DOI: 10.1007/s11661-007-9123-8

[10] S.R. Agnew, J.A. Horton, T.M. Lillo, D.W. Brown, Enhanced ductility in strongly textured magnesium produced by equal channel angular processing, Scripta Mater. 50 (2004) 337-381.

DOI: 10.1016/j.scriptamat.2003.10.006

[11] B. Chen, D.L. Lin, L. Jin, X.Q. Zeng, Ch. Lu, Equal-channel angular pressing of magnesium alloy AZ91 and its effects on microstructure and mechanical properties, Mat. Sci. Eng. A483-484 (2008) 113-116.

DOI: 10.1016/j.msea.2006.10.199

[12] J. Gubicza, K. Máthis, Z. Hegedűs, G. Ribárik, A.L. Tóth, Inhomogeneous evolution of microstructure in AZ91 Mg-alloy during high temperature equal-cannel angular pressing, J. of Alloys and Comp. 492 (2010) 166-172.

DOI: 10.1016/j.jallcom.2009.11.150

[13] C.W. Chung, R.G. Ding, Y.L. Chiu, M.A. Hodgson, W. Gao, Microstructure and mechanical properties of an as-cast AZ91 magnesium alloy processed by equal channel angular pressing, IOP Conf. Series: Mat. Sci. and Eng. 4 (2009) 012012.

DOI: 10.1088/1757-899x/4/1/012012

[14] Y.Z. Lü, Q.D. Wang, W.J. Ding, X.Q. Zeng, Y.P. Zhu, Fracture behaviour of AZ91 magnesium alloy, Materials Letters 44 (2000) 265-268.

DOI: 10.1016/s0167-577x(00)00041-0

[15] G. Eisenmeier, B. Holzwarth, H.W. Höppel, H. Mughrabi, Cyclic deformation and fatigue behaviour of the magnesium alloy AZ91, Mat. Sci. Eng. A319-321 (2001) 578-582.

DOI: 10.1016/s0921-5093(01)01105-4