Low Cycle Fatigue and Creep-Fatigue Interaction Behaviour of Reduced Activation Ferritic Martensitic (RAFM) Steels with Varying W and Ta Contents

Abstract:

Reduced activation ferritic/martensitic (RAFM) steels are candidate materials for the test blanket modules of ITER. Several degradation mechanisms such as thermal fatigue, low cycle fatigue, creep fatigue interaction, creep, irradiation hardening, swelling and phase instability associated irradiation embrittlement must be understood to estimate the component lifetime. The current work focuses on the effect of tungsten and tantalum on low cycle fatigue (LCF) and creep-fatigue interaction (CFI) behavior of four RAFM steels with varying W and Ta contents. Total strain controlled LCF experiments were performed under various strain amplitudes in the range +0.25% to +1% and temperatures (300 K to 873 K) in air at a constant strain rate of 3×10^-3s^-1 using a servo hydraulic fatigue testing system. CFI experiments were carried out at total strain amplitude of +0.6% and by applying strain hold of different durations (10 min and 30 min) in peak tension and peak compression. Both LCF and CFI life of the RAFM steels improved with the increase in tungsten and tantalum contents. Based on the amount of softening during continuous cycling, tungsten content was optimized at 1.4 wt. % and the tantalum content at 0.06 wt%. Stress relaxation obtained during creep-fatigue interaction studies showed close relation with the chemical composition of the RAFM steels. Other damaging parameters influencing fatigue life were dynamic strain ageing (DSA) occurring in the intermediate temperature regime and oxidation at elevated temperatures. Keywords: RAFM steel, low cycle fatigue, dynamic strain ageing, creep-fatigue interaction, oxidation

• Periodical: Advanced Materials Research (Volumes 891-892)
• Pages: 383-388
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.891-892.383
• Online since: March 2014
• Authors: R. Sandhya, Vani Shankar, K. Mariappan, M.D. Mathew, Tammana Jayakumar, Ellappan Rajendra Kumar
• Keywords: Creep-Fatigue Interaction, Dynamic Strain Aging (DSA), Low Cycle Fatigue, Oxidation, RAFM Steel

References

[1] A. Paúl, A. Beirante, N. Franco, E. Alves, J.A. Odriozola, Phase transformation and structural studies of EUROFER RAFM alloy, Mater. Sci. Forum 514/516 (2006) 500–504.

DOI: 10.4028/www.scientific.net/msf.514-516.500

[2] F. Abe, T. Noda, H. Araki, S. Nakazawa, Alloy composition selection for improving strength and toughness of reduced activation 9Cr-W steels, J. Nucl. Mater. 179/181 (Part 1) (March–April 1991) 663–666.

DOI: 10.1016/0022-3115(91)90176-8

[3] L. Schaefer, M. Schirra, Influence of thermal aging on tensile and impact bending properties of the steel grades OPTIFER and F82H mod, J. Nucl. Mater. 271/272 (1999) 455–458.

DOI: 10.1016/s0022-3115(98)00757-0

[4] T. Hasegawa, Y. Tomita, A. Kohyama, Influence of tantalum and nitrogen contents, normalizing condition and TMCP process on the mechanical properties of low-activation 9Cr–2W–0. 2V–Ta steels for fusion application, J. Nucl. Mater. 258/263 (1998).

DOI: 10.1016/s0022-3115(98)00138-x

[5] ASTM E606-92, Standard recommended practice for constant-amplitude low cycle fatigue testing, Annual Book of ASTM Standards, 1994, 03. 01, p.522–536.

[6] Ronald L. Klueh, Donald R. Harries, High-Chromium Ferritic and Martensitic Steels for Nuclear Applications, ASTM MONOGRAPH 3, Chapter 2, (2001).

DOI: 10.1520/mono3-eb

[7] Baldev Raj, T. Jayakumar, Development of reduced activation ferritic–martensitic steels and fabrication technologies for Indian test blanket module, J. Nucl. Mater., 417, Issues 1–3 (2011) 72-76.

DOI: 10.1016/j.jnucmat.2011.02.032

[8] B. Fournier, M. Sauzay, A. Renault, F. Barcelo, A. Pineau, Microstructural evolutions and cyclic softening of 9%Cr martensitic steels, J. Nucl. Mater. 386/388 (386) (2009) 71–80.

DOI: 10.1016/j.jnucmat.2008.12.061

[9] S. Kim, J.R. Weertman, Investigation of microstructural changes in a ferritic caused by high temperature fatigue, Metall. Trans. A 19 (1988) 999–1007.

DOI: 10.1007/bf02628384

[10] Vani Shankar, M. Valsan, K. Bhanu Sankara Rao, R. Kannan, S.L. Mannan, S.D. Pathak, Low cycle fatigue behavior and microstructural evolution of modified 9Cr–1Mo ferritic steel, Mater. Sci. Eng. A 437 (2006) 413–422.

DOI: 10.1016/j.msea.2006.07.146

[11] Vani Shankar, R. Sandhya, M.D. Mathew, Creep-fatigue-oxidation interaction in Grade 91 steel weld joints for high temperature applications, Mater. Sci. Eng. A 528 (2011) 8428–8437.

DOI: 10.1016/j.msea.2011.07.046

[12] Vani Shankar, K. Mariappan, A. Nagesha, G. V. Prasad Reddy, R. Sandhya, M. D. Mathew and T. Jayakumar, Effect of tungsten and tanta lum on the low cycle fatigue behavior of reduced activation ferritic/martensitic steels, Fusion Engineering and Design, Volume 87, Issue 4, 2012, 318-324.

DOI: 10.1016/j.fusengdes.2012.01.020

[13] K. Laha, S. Saroja, A. Moitra, R. Sandhya, M.D. Mathew, T. Jayakumar and E. Rajendran, Development of India Specific RAFM steel through optimization of tungsten and tantalum contents for better combination of impact, tensile, low cycle fatigue and creep properties, Journal of Nuclear Materials, Issues 1-3, August 2013, 41-50.

DOI: 10.1016/j.jnucmat.2013.03.073

[14] K. Mariappan, Vani Shankar, R. Sandhya, G.V. Prasad Reddy, M.D. Mathew, Dynamic strain aging behavior of modified 9Cr–1Mo and reduced activation ferritic martensitic steels under low cycle fatigue, Journal of Nuclear Materials, Volume 435, Issues 1–3(2013).

DOI: 10.1016/j.jnucmat.2012.12.049